Filed Under (Ford) by admin on 03-02-2012
…ule by squeezing the side tabs at the finish of the fitting and pulling the line apart from the fitting. 9. Unscrew the fuel pump module from the gasoline tank using the fuel tank sender wrench quantity 310-069 or equivalent. 10. Remove the fuel pump module and O-ring seal from the fuel tank. Ford Escape Fuel Pump Installation Instructions 1. Remove the previous gas pump from the module and install the brand new unit using a pair of slip joint pl…
Filed Under (Buick) by admin on 21-02-2012
he drip pan. 10. Spray engine components cleaner on a rag and gently wipe the inside of the fuel pump mounting surface. Don’t wipe the interior edge of the circle. This edge is razor sharp and will sever your finger(s). 11. Inspect all the tank for moisture spots. Spots of moisture could point out that you have a leak in your fuel tank. If the tank is leaking, then that is the time to exchange it. 12. Inspect the new fuel pump to make sure…
Filed Under (Ford) by Doe on 18-05-2014
the tip of the metallic outlet line onto the underside of the pump. 10. Press the tip of the rubber inlet line onto the metallic nipple on the underside of the pump, then tighten the road’s clamp till the road is safe. 11. Reattach the negative battery cable to the battery by tightening the nut on the tip of the cable with a wrench….
Filed Under (Ford) by admin on 15-11-2012
tip of the steel outlet line onto the bottom of the gas pump. 10. Press the tip of the rubber inlet line onto the metallic nipple on the underside of the fuel pump, then tighten the line’s clamp till the line is secure. 11. Reattach the unfavourable battery cable to the battery by tightening the nut on the tip of the cable with a wrench….
Filed Under (Ford) by admin on 08-05-2013
…minal. 8. Fill the tank with not less than 5 gallons of fuel and pressurize the fuel system. With the Fuel Pump relay and fuse related and the gas cap on, turn the ignition on for 2 seconds. Switch it off and leave it off for 10 seconds before switching it on again. Repeat this five to 10 times….
Filed Under (Ford) by admin on 22-04-2013
…e fuel pump relay. 7. Connect the black, adverse battery cable utilizing the wrench. 8. Flip the ignition key to “On” but don’t start the vehicle. Make sure that there are no leaks on the filter connections. 9. Start the engine and let it idle. Double-test for leaks….
Filed Under (Chrysler) by Doe on 21-07-2014
…m each again beneath the LHS. 9. Reverse the way in which you put in the fuel tank and reinstall. Decrease the LHS off the jack stands together with your ground jack. Rehook the battery cable to the battery and shut the hood. 10. Flip the ignition key to the run position for ten seconds; it will prime the fuel system earlier than beginning the automobile. It might be essential to repeat this step earlier than the LHS will begin. Read more : How t…
Filed Under (Ford) by admin on 05-05-2012
ck and operates at three to four pounds per sq. inch, which is far lower than modern fuel-injected engines. You could want to install a new fuel pump if your 223 six is difficult to start or stumbles on acceleration. Ford 233 6-Cylinder Engine Fuel Pump Installation Instructions 1. Open the hood. Locate the fuel pump, mounted to the driving force’s facet of the engine block, roughly halfway between the entrance and rear of the motor. 2. Loo…
Filed Under (Toyota) by admin on 23-02-2012
ch. 7. Press the vent line on its fitting until the lock snaps in place; then set up the fuel line and safe it with the clip; plug the fuel pump vapor stress sensor electrical connector and the fuel pump electrical connector. 8. Join the black, adverse battery cable and set up the fuel tank filler cap. Start the engine and test for leaks; then flip off the engine and set the fuel pump assembly service cowl in place. Set up the mounting screws or…
Filed Under (Audi) by Doe on 15-07-2014
e outdated gas pump within the drain pan. 8. Use Audi device #3307 with the socket wrench to insert the brand new fuel pump. Flip the pump clockwise barely to lock, after which connect the electrical connectors and the hoses. 9. Reinstall the fuel tank nut cowl utilizing Audi device #3217 with the torque wrench. Tighten the nut to 50 foot-kilos. Replace the trunk ground lining and the carpet, reconnect the negative battery cable and exchange the…