Search Result for " where is factory amp located 2006 trailblazer ext" :

Loss of Communication with Brake Module (Reground EBCM Ground)

27

Filed Under (Cadillac, Chevrolet, GMC, Oldsmobile) by admin on 09-04-2013

hers and nuts specified in this bulletin. These parts have been identified because of their conductive finish. 4. Install a washer and nut to the back facet of the frame. Tighten Tighten the nut to 9 N·m (seventy nine lb in). 5. Cover the front and back aspect of the restore area using Rubberized Undercoating. An additional test may be made to ensure an excellent connection for the Battery Cable to Body ground. It’s potential for this groun…

Ford Ranger Amplifier Installation Instructions

30

Filed Under (Ford) by admin on 04-04-2013

…ss adapter. 6. Feed the amplifier cables, from the wiring harness adapter, by means of the opening in the back left panel of the stereo mounting dock. The wiring will emerge in the footwell area on the passenger’s side. 7. Position the stereo into the stereo mounting dock by pushing the unit into the sprint and eradicating the Ford elimination keys. 8. Place the amplifier beneath the motive force or passenger’s seat of the truck. Plac…

Ford SuperCrew Amplifier Installation Instructions

29

Filed Under (Ford) by admin on 07-03-2013

…on the truck’s battery by loosening the screw and sliding the lead off the post. Place the ring on the end of the power cable over the post and slide it down. Replace the battery lead to the post and tighten the screw. 7. Drill a hole through the firewall large enough to feed the power cable through. Place a rubber grommet into the hole to protect the cable. 8. Run the power cable from the battery to the amplifier and connect it to the pow…

Honda Civic Reverse Glow Gauges Installation Procedures

35

Filed Under (Honda) by admin on 17-06-2012

n the similar time. It shouldn’t require a variety of power to pull of the needle, nonetheless, relying on the age of your Civic, the needle may be caught on there pretty good.Repeat this process for every gauge needle. 7. Place the brand new gauge faces over the factory gauge faces and middle them. 8. Use the knife to chop a slit within the bottom of the factory gauge cluster to accommodate the new gauge face wires. A typical location for…

Honda Element Subwoofer Installation Procedures

35

Filed Under (Honda) by admin on 14-01-2014

of the vehicle to the rear cargo area. Place the powered subwoofer behind the Element and join the grounding wire (from the amp wiring equipment) from the sub to a screw or bolt immediately linked to the Honda’s frame. 7. Plug the ability cable into the facility input on the sub. Join the patch cables to the signal and switch-on lead shops on the subwoofer. 8. Substitute the negative battery cable clamp onto the negative battery terminal p…

Ford Ranger Body Lift Kit Installation Instructions

31

Filed Under (Ford) by admin on 19-02-2012

…body lift pucks onto the manufacturing unit bushings. 4. Slide the body lift pucks into position on prime of the factory bushings. Do not remove the factory bushings. Lower the vehicle body onto the newly put in carry pucks. 5. Install the new bolts into place and tighten them utilizing a ratchet and socket. Confirm that all six bolts are tight. Re-set up the bumper, fan, and shroud utilizing a socket and ratchet. Ford Ranger Bed Portion of the…

Ford Escape Audio Subwoofers Installation Instructions

22

Filed Under (Ford) by admin on 11-11-2012

…the wiring teams from the Ford to a wiring harness adapter. Connect the wiring harness adapter to the stereo. The wiring harness leads will likely be marked to determine which connections go into which of the stereo outlets. 7. Connect the sign cable and switch-on lead (each offered in the amplifier wiring package) to the wiring harness adapter. Route the cables from inside the stereo dock, beneath the carpeting, to the rear cargo area of the Es…

Toyota Camry Sirius Car Radio Installation Instructions

36

Filed Under (Toyota) by admin on 23-02-2012

a wire along the path of the Camry’s rear speaker wiring harness to the front of the vehicle just beneath the center console. Use a putty knife to create an opening along the interior trim panels securing the carpeting. 7. Attach the antenna wire to the socket on Sirius dock. The connection point is labelled “ANT.” Coil the remaining wire with twist-ties. 8. Mount the sirius radio onto the dock. Plug the cigarette lighter adapte…

Honda Civic Angel Eyes Headlight Installation Procedures

33

Filed Under (Honda) by admin on 30-05-2012

ting from the tip of the wires and then wrap them together and connect them to the back of the lights. Use the clamps on the back of the lights to maintain them in place. Solely strip off an inch or so of the plastic coating. 6. Change the bumper cover and the negative battery connector. Activate the lights to make sure they work and all wiring is connected….

Toyota Corolla Remote Starter Installation Instructions

48

Filed Under (Toyota) by admin on 23-03-2012

…wires subsequent to manufacturing unit wire harnesses, and connect them with nylon wire ties. 4. Mount the antenna to the windshield. For maximum range, mount the antenna as close to the center of the windshield as possible. 5. Test the unit for correct operation. Verify the correct operation of the remote begin and all installed functions. Arm the manufacturing unit alarm, if geared up, and confirm that the alarm does not go off when the automo…

You might also likeclose