Search Result for " vacuum lines on valve cover 2003 gmc yukon denali" :

Honda Accord Valve Cover Gasket Installation Procedures

21

Filed Under (Honda) by admin on 15-06-2012

…6. Take away the previous valve cover gasket from the valve cover, and rub the cylinder head surface with wonderful sandpaper so that the new gasket has a clear floor to adhere to. 7. Place the new gasket on the valve cover. 8. Place the valve cover onto the cylinder head, and tighten the valve cover bolts to about 15 foot-lbs. with a torque wrench. 9. Reinstall the spark plug wires, and place the spark plug wire cover again onto the valve cover

Ford Explorer EGR Valve Installation

31

Filed Under (Ford) by admin on 08-01-2012

…ts with your socket wrench and pull the valve from the intake manifold. 6. Utilizing a thin metal paint scraper, make certain the previous gasket that sat between the EGR valve and the consumption manifold is totally removed. 7. Lay the brand new EGR valve gasket into place and insert the new valve into the intake manifold. Re-install the EGR valve mounting bolts and hand tighten. Now, re-join the tubes and hoses that you just removed and exchang…

Ford EGR Valve Replacement Instructions

34

Filed Under (Ford) by admin on 27-04-2013

on’t tighten them yet. Start the pipe threaded fitting by hand to keep away from harm to the threads. Then tighten the mounting bolts and threaded nut. Connect the vacuum hose or hoses and plug the electrical connector. 8. Set up the air consumption meeting and engine cover….

Toyota Camry EGR Valve Removal and Installation Instructions

40

Filed Under (Toyota) by admin on 23-02-2012

…ove the Evaporative Emissions (EVAP) management hose from the hook positioned on the EGR valve. 4. Unplug the vacuum hose or hoses from the EGR valve. 5. Detach the EGR valve utilizing a ratchet, ratchet extension and socket. 6. Take away the EGR valve and gasket from the engine compartment. Toyota Camry EGR Valve Removal Instructions 1. Set the brand new EGR valve and new gasket in place. 2. Start the EGR valve mounting bolts and/or nuts by hand…

Replace Evaporative Emission Vent Valve Solenoid – Page 1

22

Filed Under (Chevrolet, GMC) by admin on 14-12-2011

valve assembly to the frame bracket on the surface of the body utilizing the existing hole and mounting bolt. 7. Tighten Tighten the bracket mounting bolt to 12 N—m (106 lb in). Join the vent valve pipe to the EVAP canister. 8. Install the two vent valve pipe clips into the present underbody holes. 9. Connect the EVAP canister vent valve electrical connector, if equipped. 10. Connect bulk 5/8″ heater hose to the vent valve port and safe ut…

Loss of Communication with Brake Module (Reground EBCM Ground)

27

Filed Under (Cadillac, Chevrolet, GMC, Oldsmobile) by admin on 09-04-2013

hers and nuts specified in this bulletin. These parts have been identified because of their conductive finish. 4. Install a washer and nut to the back facet of the frame. Tighten Tighten the nut to 9 N·m (seventy nine lb in). 5. Cover the front and back aspect of the restore area using Rubberized Undercoating. An additional test may be made to ensure an excellent connection for the Battery Cable to Body ground. It’s potential for this groun…

2001 F-150 Intake Manifold 5.4L Removal Procedure

25

Filed Under (Ford) by admin on 15-11-2012

e the bolts. Remove the accelerator cable snow shield. 7. Disconnect the throttle body cam. Disconnect the accelerator cable (9A758). Disconnect the velocity management actuator cable. Take away the accelerator return spring. 8. Take away the accelerator cable bracket bolts and position the bracket and cables aside. 9. Disconnect the vapor management valve hose. Remove the crankcase ventilation tube and the idle air control (IAC) valve recent air…

1998-2002 Honda Accord V6 Comptech Supercharger Kit – Page 2

34

Filed Under (Honda) by admin on 05-03-2013

re against the bracket to distort plate or push it out, this spacer is only designed to take up inconsistencies in factory head. Whereas holding spacer with a 19mm wrench, insert supplied 10mm bolt into gap and torque bolt to 28ft-lbs. Torque cam seal bolts (B) to 15ft/lbs. Change EGR valve, utilizing provided gasket, and torque to 15ft/lbs. Substitute electrical plug. 12. Blower preparation : Blower has (6) bolts around enter shaft. Lower (4) bo…

2001 Lincoln LS Intake Manifold Removal Procedure

40

Filed Under (Lincoln) by admin on 26-10-2012

Remove the EGR valve. Remove the 2 bolts. Take away the valve and discard the gasket. 7. Disconnect the camshaft position (CMP) sensor electrical connector and separate the connector from the fuel injection provide manifold. 8. CAUTION: To remove normal fittings, squeeze the tabs and pull straight out or harm to the fitting might occur. Disconnect the evaporative emission canister purge valve line. 9. Disconnect the gas strain sensor electrical…

Replace Evaporative Emission Vent Valve Solenoid – Page 2

29

Filed Under (Chevrolet, GMC) by admin on 16-04-2013

d the canister pipe and secure using clamps. 7. Attach bulk 5/8″ heater hose to the vent valve port and safe utilizing a clamp. Run a length as needed alongside the body rail routing to the world above the transmission. 8. Cut the hose to decided size and set up the provided filter box. Safe using a clamp. 9. Secure the filter box to the transmission vent hose just forward of the hose tee*part utilizing a tie strap. DO NOT pinch or limit th…

You might also likeclose