Search Result for " toyota corolla 1998 power steering hose replace" :

Install Power Steering Pressure and/or Return Hose Assembly

39

Filed Under (Buick, Pontiac) by admin on 02-05-2013

ing pump assembly. Take away the bolt/screws from the retaining clips. 5. Disconnect the ability steering strain hose from the ability steering gear assembly. Take away the power steering stress hose meeting from the vehicle. 6. Set up the ability steering pressure hose assembly to the vehicle. Join the power steering strain hose to the facility steering pump assembly. 7. Connect the facility steering stress hose to the power steering gear assemb…

Toyota Steering Intermediate Shaft Noise Repair

26

Filed Under (Toyota) by admin on 09-10-2014

shaft sub-assembly with the bolt. Torque: 35.three Nm (360 kgfcm, 26 ftlbf) c. Set up the steering column hole cowl to the steering gap cowl boot. d. Join the clamp to the steering column gap cover boot and tighten the bolt. 6. Take away the steering wheel holder from the car (if used). 7. Road test the car to confirm the restore and make sure that the steering wheel is centered….

Ford Focus Steering Rack Installation Instructions

32

Filed Under (Ford) by admin on 19-02-2012

sion jack and subframe alignment pins to reconnect the ability steering hoses. Tighten the hose assist clamp and change the heat shield. Safe the support insulator to the transaxle middle bolt with a torque of 37 foot pounds. 6. Join the cooler hose and relink the stabilizer bars to the struts and springs (37 foot pound torque). Tighten the new tie rod end nuts to 35 foot-pounds and exchange the wheels. You may decrease the front end at this poin…

Toyota Corolla Exhaust Removal and Installation Instructions

30

Filed Under (Toyota) by admin on 04-03-2012

tive installation. 5. Unbolt the chassis brace, located beneath the front pipe. The entrance pipe is located after the resonator assembly. Take away the entrance pipe and place it off to the facet along with all its hardware. 6. Take away the original resonator assembly in case your new exhaust system features a replacement resonator. In this case, reduce the unique resonator piping one to a few inches in entrance of the weld melding the resonato…

1998-2002 Toyota Corolla Exterior Door Handles Installation Instructions

38

Filed Under (Toyota) by admin on 24-02-2012

mall pole into the clip of the upper portion of the new handle. Take a look at the handle to ensure the door latches and unlatches properly. Set up the three 10 millimeter bolts and tighten. Reattach the clear plastic lining. 4. Place the remaining portion of the door panel onto the six plastic clips on the outer portion of the panel. Pull it over the inside door lock. Make sure that the interior door opener can be positioned by way of the suppli…

Ford Focus Power Steering Pump Installation Instructions

39

Filed Under (Ford) by admin on 30-04-2013

…f the pump, and drain the pump into the cup. 3. Take away the nuts which can be holding the pump onto the firewall, utilizing the wrench. Remove the belt on the pump from the pulley. Pull the old pump from the engine housing. 4. Secure the new pump onto the firewall with the securing nut. Exchange the belt to the pulley on the pump. Exchange the strains to the right holes on the pump. Tighten the nuts on the firewall and pump lines. Fill the pump…

Toyota Corolla Car Alarm Installation Instructions

37

Filed Under (Toyota) by admin on 23-02-2012

dash. 5. Join the power, LED, siren, door lock and disable relay wires to the management module. Mount the control module as far into the dash as attainable by securing it to a heavy wire bundle or cross member with zip ties. 6. Reconnect the constructive battery cable on the Toyota Corolla and take a look at the alarm. Modify the alarm’s sensitivity as needed and safe any free wires with zip ties….

1998-2002 Honda Accord V6 Comptech Supercharger Kit

34

Filed Under (Honda) by admin on 05-03-2013

oir bracket. Loosen inventory alternator belt tensioner and remove stock alternator belt. Remove decrease bolt on alternator then take away upper bolt. Remove bracket connected to top of alternator. These bolts can be reused. 6. Alternator pulley alternative : With alternator pulley dealing with up take away inventory alternator pulley with a 22mm & 10mm wrench (an affect gun might must be used for removal). Install new alternator pulley (Se…

Buick Steering Wheel Installation Instructions

30

Filed Under (Buick) by admin on 29-03-2013

…ering wheel puller tool onto the steering wheel and break the steering wheel loose from the steering column. Remove the steering wheel bolt and nut with a socket wrench and pull the old steering wheel off the steering column. 6. Place the new steering wheel onto the steering column and secure it with the nut and bolt. 7. Reattach the horn cap and its electrical connector as well as the steering wheel cover and its electrical connector. Secure the…

Toyota Corolla Car Stereo Installation Instructions

32

Filed Under (Toyota) by admin on 10-05-2013

ps, which interact automatically. 5. Plug the wiring harness adaptor and antenna wire into the again of the new head unit and push the whole meeting into the dash. Reconnect the damaging battery cable and switch the radio on. 6. Ensure all of the stereo controls and speakers are working. Safe the radio in the dash with the unique 4 screws and exchange the trim….

You might also likeclose