Search Result for " shift solenoid 2001 buick lesabre" :

Buick LeSabre Brake Pads Installation Instructions

55

Filed Under (Buick) by admin on 25-05-2012

…. 2. Remove the front hubcaps and loosen the wheel nuts utilizing the lug wrench, however don’t take away the nuts. 3. Elevate the entrance end of the LeSabre with the ground jack and secure safely onto the jack stands. 4. Take away the wheel nuts and wheels. Screw one wheel nut back onto a wheel stud hand tight to retain the rotor away from the caliper assembly. 5. Place a big C-clamp over the left inboard caliper housing and the outboard…

Install Power Steering Pressure and/or Return Hose Assembly

39

Filed Under (Buick, Pontiac) by admin on 02-05-2013

-2001 Pontiac Bonneville. Power Steering Pressure (Inlet) Hose Replacement Procedure 1. Raise and suitably support the vehicle. 2. Drain the ability steering fluid. 3. Remove the ability steering gear assembly warmth shield. 4. Disconnect the facility steering stress hose from the facility steering pump assembly. Take away the bolt/screws from the retaining clips. 5. Disconnect the ability steering strain hose from the ability steering gear asse…

Buick LeSabre Radio/Stereo Replacement Instructions

28

Filed Under (Buick) by admin on 22-02-2012

…d work your approach to the other, popping the clips unfastened as you go. Take away the panel and set it aside. 3. Use a flat-head screwdriver to come out the AC vents. Take away the only Phillips screw in every vent cavity. 4. Use the screwdriver to pry the trim panel free around the radio. Clips also hold the radio panel in place. Apply outward pressure to disengage the clips and take away the panel. 5. Take away the Phillips screws holding th…

Buick Lesabre Radio Installation Instructions

38

Filed Under (Buick) by admin on 22-05-2012

…ss. Find the plug connection on the again of the new radio for the electrical wiring from the factory harness. It will usually be a six-pin connector, but could also be a 12-pin connector relying on the year of your LeSabre . 3. Slide the radio into the dash till the unit locks into place. Obviously, the antenna and wiring facet of the radio is inserted into the dash. When the unit is totally put in, you need to hear a click indicating that the u…

2000 Buick LeSabre Window Regulator Installation Instructions

28

Filed Under (Buick) by admin on 22-02-2012

l away from the door along with your trim tool. Lift the door panel up and off the door, ensuring to push the inner door handle by the opening so that it clears the door panel earlier than moving the panel away from the door. 4. Push the window glass to the highest of the window body and secure it there with packing tape by wrapping the tape from the glass, up and over the door body and down onto the opposite aspect of the glass. 5. Unbolt the wi…

Buick LeSabre Serpentine Belt Installation Instructions

36

Filed Under (Buick) by admin on 22-02-2012

…tact and assist among the weight. Remove the coolant overflow bottle. Take away the bolts attaching the motor mount to the frame, as well as the motor bracket. Then elevate out the motor mount and take away the previous belt. 4. Set up the brand new belt, referring to the belt routing drawing or service handbook, and slip it again onto the alternator whereas compressing the spring-loaded tensioner. Reinstall the motor mount and coolant overflow b…

Buick LeSabre Crankshaft Position Sensor Installation Instructions

25

Filed Under (Buick) by admin on 21-02-2012

harmonic balancer puller, then take away the harmonic balancer. Disconnect the electrical plug from the crankshaft sensor. Remove the 2 bolts securing the sensor to the block. Remove the old sensor from its mounting pedestal. 4. Install the brand new sensor with pedestal on the particular set up tool. Move the crankshaft sensor so that the software’s blades go useless heart by way of the sensors with out making contact. Tighten the sensor a…

Vibration in Steering Wheel, Floor, Seat at Highway Speeds

35

Filed Under (Buick, Cadillac, Oldsmobile, Pontiac) by admin on 18-01-2012

n. Record the Hertz (Hz) reading as displayed via the EVA onto the tire knowledge worksheet found on the finish of this bulletin. This will have to be done after a tire break-in period of a minimum of 10 miles (sixteen km) at 45 mph (72 km/h) or greater, to be able to eliminate any conceivable tire flat-spotting. 4. If the road test indicates a shake/vibration nonetheless exists, check the imbalance of each tire/wheel assembly on a identified, ca…

Buick Trailer Wiring Kit Installation Instructions

36

Filed Under (Buick) by admin on 28-03-2013

…produced with a tow package, and on the crossovers it is obtainable only as an added-price option, so none are manufacturing facility-fitted with a wiring harness for trailer towing. However, retrofitting a Buick with a flat 4-pin hitch, out there from most auto elements stores and the truck aisle of most residence enchancment warehouses, is an easy project. Buick Trailer Wiring Kit Installation Instructions 1. Discover the wiring harnesses serv…

Buick Car Radio Installation Instructions

37

Filed Under (Buick) by admin on 27-07-2014

e away the two screw bolts on both facet of the manufacturing facility stereo with the 7-mm socket and ratchet. Slide the stereo from the dashboard and disconnect the stereo wiring and antenna cable from the back of the unit. 4. Insert the faceplate adapter into the stereo dock. Feed the stereo wiring through the faceplate adapter in order that it’s accessible from the front of the Buick’s dashboard. Plug the stereo wiring connectors…

You might also likeclose