replace fuel rail pressure sensor 2004 ford explorer

You search Auto repair manual PDF about replace fuel rail pressure sensor 2004 ford explorer, search results will appear below. If search results do not exist, please search by others keyword.

pdf download  Free Download replace fuel rail pressure sensor 2004 ford explorer.pdf

Ford Explorer Fuel Tank Installation Instructions


Filed Under (Ford) by admin on 18-04-2013

apor hose to the tank. Examine the wiring and hoses on and around the tank to see if something is loose or damaged. Change any damaged hoses or wires. If every thing is OK, fill your Explorer’s tank with gasoline again. 6. Test your Explorer’s driving means after you’ve installed the fuel tank. Let the automobile’s engine run briefly, then take a brief trip. Observe how your Explorer runs and keep your manual handy in case…

Ford Escape Fuel Pump Removal and Installation Instructions


Filed Under (Ford) by admin on 03-02-2012

…by hand. 4. Lift the carpet underneath the seat. 5. Detach the access door on the floor to reach gasoline pump module on the fuel tank. Use a Phillips screwdriver. 6. Unplug the electrical connectors on the fuel pump module. 7. Disconnect the gas pump module from the gas lines utilizing the half of-inch disconnect instrument quantity 310-D005 or equivalent. 8. Unplug the vapor gas line at the gas pump module by squeezing the side tabs at the fin…

Ford DPFE Sensor Installation Instructions


Filed Under (Ford) by admin on 03-01-2012

…ct tabs and pull the harness out. Use a socket wrench to loosen and remove the sensor’s screws. Raise the sensor off the mount. 4. Wipe the mount clean with a rag. This will ensure a clean connection for the new sensor. 5. Set up the new DPFE sensor. Place the sensor on the mount. Safe the sensor with the 2 screws and tighten with the socket wrench. Plug the hoses into the new sensor. Join the wire harness; the harness will click on into pl…

Ford Escape Fuel Filter Removal and Installation Instructions


Filed Under (Ford) by admin on 22-04-2013

…he screwdriver or ratchet and socket. 3. Attach the fuel traces to the fuel filter fittings. 4. Set up new lock tabs to the fittings to safe the fuel traces to the filter. 5. Decrease the vehicle. 6. Plug the fuel pump relay. 7. Connect the black, adverse battery cable utilizing the wrench. 8. Flip the ignition key to “On” but don’t start the vehicle. Make sure that there are no leaks on the filter connections. 9. Start the engi…

Ford F-150 Fuel Injector Installation Instructions


Filed Under (Ford) by admin on 01-04-2013

…st to the bumper and pop each Fuel Injector free. Some injectors will keep in the engine and others will stay in the gasoline rail. All injectors which might be freed from either the engine or fuel rail will want new o-rings. 6. Remove the gas injector from each the engine and the gasoline rail. Examine the injector for missing o-rings. Two o-rings ought to exist, one for the highest connection on the gas rail, and one for the underside connectio…

Ford Focus Oxygen/O2 Sensor Installation Instructions


Filed Under (Ford) by admin on 20-04-2013

…t the propane torch and warmth the area of pipe across the O2 sensor to broaden the pipe. Take away the O2 sensor as soon as the pipe expands sufficient to launch it, however then permit ample time for the pipe to chill down. 7. Screw the new O2 sensor into the porthole within the exhaust pipe and tighten with the ratchet and socket. Watch out not to over-tighten. Plug the wire back into the connector, gather the tools and crawl out from beneath…

Ford Explorer Water Pump Removal and Installation Instructions


Filed Under (Ford) by admin on 10-01-2012

…l the radiator with the quantity and type of coolant laid out in your owner’s manual. 4. Take away the jack stands and launch the jack. Attach the negative battery cable to the put up and tighten the screw on the clamp. 5. Begin the engine and verify for leaks. Then, close the hood and take the SUV for a test drive….

Audi A4 Fuel Pump Replace Procedures


Filed Under (Audi) by Doe on 15-07-2014

o remove the nut. With the nut eliminated, you’ll acquire entry to the fuel pump. 6. Label the fuel pump hoses for enter and output; you want to have the ability to correctly join the strains to the brand new fuel pump. 7. Use Audi device #3307 with the socket wrench to remove the fuel pump. Barely flip the fuel pump counterclockwise to unlock it for removing. Rigorously disconnect the traces, with the pump wrapped in a towel, to reduce lea…

Toyota Corolla Fuel Filter Installation Instructions


Filed Under (Toyota) by admin on 23-02-2012

nch, align the indented mark on the tank with the tab on the fuel pump assembly mounting surface; align the mark on the retainer ring with the earlier marks and rotate the ring 2 complete turns using the fuel lock nut wrench. 7. Press the vent line on its fitting until the lock snaps in place; then set up the fuel line and safe it with the clip; plug the fuel pump vapor stress sensor electrical connector and the fuel pump electrical connector. 8….

Ford F-350 Fuel Pump Installation Instructions


Filed Under (Ford) by admin on 08-05-2013

…any O-rings on the coupling. Press any locking tabs into their locked position. 6. Install the skid plate on the tank and safe its mounting nuts with the wrench. Decrease and remove the ground jack holding the tank in place. 7. Attach the wheel back on the truck using the inventory tire iron or one among your own, and lower the truck. Connect the cable to the negative battery terminal. 8. Fill the tank with not less than 5 gallons of fuel and pr…