Search Result for " replace evaporator on 01 toyota corolla" :

Toyota Corolla Exhaust Removal and Installation Instructions

30

Filed Under (Toyota) by admin on 04-03-2012

d position. 4. Place the muffler meeting and all the corresponding hardware and insulators off to the side. Do not lose any of these parts as a result of they may be used in the course of the exhaust alternative installation. 5. Unbolt the chassis brace, located beneath the front pipe. The entrance pipe is located after the resonator assembly. Take away the entrance pipe and place it off to the facet along with all its hardware. 6. Take away the…

Toyota Corolla Car Stereo Installation Instructions

32

Filed Under (Toyota) by admin on 10-05-2013

yota radio mounting kit, which is a thin metal cover and secure it per the manufacturer’s instructions. Most adaptors have screws to carry the stereo in place, nevertheless some have clips, which interact automatically. 5. Plug the wiring harness adaptor and antenna wire into the again of the new head unit and push the whole meeting into the dash. Reconnect the damaging battery cable and switch the radio on. 6. Ensure all of the stereo cont…

Toyota Corolla Fuel Filter Installation Instructions

26

Filed Under (Toyota) by admin on 23-02-2012

ing the line off the assembly. When you’ve got a 2002, 2003 or 2004 model Toyota Corolla, unscrew the retainer ring mounting bolts using a Phillips screwdriver; otherwise, use a fuel lock nut wrench to unscrew the ring. 5. Carry the fuel pump meeting off the fuel tank and discard the O-ring situated between the meeting and fuel tank. Take away the Fuel Filter from the meeting and install the new unit. 6. Install a new O-ring and set the fue…

Toyota Corolla Remote Starter Installation Instructions

48

Filed Under (Toyota) by admin on 23-03-2012

…wires subsequent to manufacturing unit wire harnesses, and connect them with nylon wire ties. 4. Mount the antenna to the windshield. For maximum range, mount the antenna as close to the center of the windshield as possible. 5. Test the unit for correct operation. Verify the correct operation of the remote begin and all installed functions. Arm the manufacturing unit alarm, if geared up, and confirm that the alarm does not go off when the automo…

Toyota Corolla Car Alarm Installation Instructions

37

Filed Under (Toyota) by admin on 23-02-2012

place. 4. Mount the shock sensor per the producer’s directions and find the starter wire within the ignition harness in the steering wheel column. Connect the start disable relay and run all the wires beneath the dash. 5. Join the power, LED, siren, door lock and disable relay wires to the management module. Mount the control module as far into the dash as attainable by securing it to a heavy wire bundle or cross member with zip ties. 6. R…

Toyota Corolla Spoiler Installation Instructions

38

Filed Under (Toyota) by admin on 20-01-2013

trunk. Transfer that measurement to the trunk lid. Set the spoiler back on the trunk and double examine your measurements, tilting the spoiler up and down to ensure the holes you’re about to drill are in the best spots. 5. Drill the holes in the trunk lid utilizing the drill and metal drill bits. Start off with a small diameter bit corresponding to 1/eight-inch, then step up progressively until you get to one dimension bigger than the bolts…

Toyota Corolla Interior Door Handle Installation Instructions

30

Filed Under (Toyota) by admin on 19-10-2014

ed earlier than 2004, you may need to insert the deal with slightly in entrance of the door deal with hole. If this is the case, slide it in there, then pull it towards the outer fringe of the door. It should slip into place. 5. Safe the door deal with using the screw that was faraway from the outdated handle. If that one is unavailable, go to your native auto elements retailer to search out out the size. It varies on different yr fashions and fe…

1998-2002 Toyota Corolla Exterior Door Handles Installation Instructions

38

Filed Under (Toyota) by admin on 24-02-2012

mall pole into the clip of the upper portion of the new handle. Take a look at the handle to ensure the door latches and unlatches properly. Set up the three 10 millimeter bolts and tighten. Reattach the clear plastic lining. 4. Place the remaining portion of the door panel onto the six plastic clips on the outer portion of the panel. Pull it over the inside door lock. Make sure that the interior door opener can be positioned by way of the suppli…

Toyota Corolla Fog Lights Installation Instructions

29

Filed Under (Toyota) by admin on 23-02-2012

ate a suitable place to ground them to the vehicle. Normally there are ample screws to floor to alongside the within of the engine compartment. If there isn’t a black lead, the mounting bracket will function the ground. 5. Join the red, or positive, wire of the fog light on the passenger aspect of the automotive to the purple wire on the motive force’s side. Then splice a long segment of wire (7+ ft) from the driving force’s sid…

Toyota Corolla Timing Belt Installation Instructions

24

Filed Under (Toyota) by admin on 30-03-2013

…of the tension. Loosen the belt tensioner an allow it to use rigidity on the belt. Set up the belt guide washer on the crankshaft. Flip the crankshaft two turns and realign the timing marks. Tighten the belt tensioner bolt to 27 foot kilos of torque. Install all parts in reverse order of removal and at last tighten the crankshaft bolt to 87 foot pounds of torque….

You might also likeclose