Search Result for " px ranger aftermarket headlights thailand" :

Honda Projector Headlights Installation

29

Filed Under (Honda) by admin on 20-07-2014

…the bulb and lock the bulb into the housing. Make sure that you do not contact the glass bulb with your fingers. In case you do, the bulb will explode inside the housing as soon as it heats up to regular working temperature. 4. Plug the electrical connector into the back of the bulb’s ballast. For specific details about your Honda car and the situation of your particular Honda’s headlight mounting brackets, consult the actual vehicle…

Ford Ranger Skid Plate Installation Instructions

33

Filed Under (Ford) by admin on 05-04-2013

A correctly installed Skid Plate can imply the difference between a rough ride and extreme engine damage. The purpose of the Skid Plate is to protect the Ranger’s engine from highway particles and off-street debris the truck drives over. If you go off-street together with your Ranger, a solid Skid Plate is a necessity. You should purchase an excellent skid plate from most 4×4 auto retailers. Anybody with fundamental auto-restore…

1999 Ford Ranger Extended Cabs Westin Nerf Bars Installation Instructions

35

Filed Under (Ford) by admin on 26-06-2012

l. 3. Slide the Nerf Bar mounting bolts via the mounting holes within the Nerf Bars and the Ranger’s frame. Thread the mounting nuts onto the ends of the bolts by hand. Tighten the nuts onto the bolts with a socket set. 4. Move the jack stands to the best side of the 1999 Ford Ranger and repeat the primary three steps to install the precise Westin Nerf Bar. Take away the jack stands when done. 5. Use care when setting the Nerf Bars on the j…

Ford Ranger Clutch Removal and Installation Instructions

36

Filed Under (Ford) by admin on 28-04-2013

nd shifter inside the cab of your Ranger. 2. Disconnect the exhaust pipe. 3. Take away the interior elements–the elements under the hood. This consists of the starter, which is attached to the transmission bell-housing. 4. Disconnect the drive-shaft and the hose for the hydraulic slave cylinder. 5. Use a jack to raise one side of your truck. 6. Utilizing a metric socket set, undo the transmission cross-member and bolts, which is able to hel…

Ford Ranger Stereo/Radio Installation Instructions

34

Filed Under (Ford) by admin on 13-02-2012

…complete. 2. Insert the elimination tools into the radio. There are sets of holes on either side of the radio’s face to receive the tools. 3. Pull the instruments outward and then pull the radio away from the dashboard. 4. Disconnect the white plastic wire binders from the rear of the radio. Pull the antenna cable from the unit. 5. Insert the Ford set up kit dock to receive the aftermarket radio. Feed the Ranger’s wiring by way of the…

Ford Ranger Tow Bar Installation Instructions

31

Filed Under (Ford) by admin on 17-11-2012

ent instrument, as well as the width of the tow bar. 3. Use a pencil to mark the vehicle body the place the bolt holes shall be drilled. These marks should be centered on the body based on the widths of the frame and tow bar. 4. Clamp the tow bar to the car frame and align the bar to your drill hole markings. 5. Drill the holes in the body, using the position of the tow bar as a template. 6. Insert the mounting bolts and tighten them with a wrenc…

Ford Ranger Body Lift Kit Installation Instructions

31

Filed Under (Ford) by admin on 19-02-2012

…he vehicle’s undercarriage to stop damage to the kick panels. Place the jack ready so it lifts the body of the vehicle. Only carry the automobile enough to slide the body lift pucks onto the manufacturing unit bushings. 4. Slide the body lift pucks into position on prime of the factory bushings. Do not remove the factory bushings. Lower the vehicle body onto the newly put in carry pucks. 5. Install the new bolts into place and tighten them…

Ford Ranger Front and Rear Shock Replacement Instructions

30

Filed Under (Ford) by admin on 20-02-2012

…e axle at each side. 2. Take away the tires from the axle. 3. Find the mounting bolts that secure the front shocks in place. Spray these bolts with penetrating fluid and permit the fluid to lubricate the bolts for 10 minutes. 4. Take away the lower and higher bolts that safe the Shock in position with a ratchet and socket. Remove the Shock from the Ranger. 5. Place the new shock into position. Connect it to the brackets utilizing the inventory bo…

Ford Ranger Door Lock Removal and Installation Instruction

43

Filed Under (Ford) by admin on 05-11-2012

…r. Pull the window crank off the splined shaft. 3. Pry a flat-head screwdriver between the door panel and the door and push outward to launch the plastic retainer clips. Pop the clips out one at a time to reduce harm to them. 4. Pull the door panel off and set it apart away from the work area. Unhook the door latch rod from the retaining clip. 5. Slide the lock cylinder retainer away from the lock cylinder using a pair of pliers. Pull out the Doo…

Ford Ranger Starter Motor Installation Instructions

29

Filed Under (Ford) by admin on 01-05-2013

…nd. Make sure the jack stand is below the correct entrance frame, but doesn’t impede your access to the starter. 3. Climb underneath the Ranger with the socket set and unbolt the starter wiring utilizing the socket set. 4. Support the physique of the starter with one hand when you take away the 2 starter-mounting bolts with the socket set utilizing your different hand. Do not let the starter rest on the loose bolts at any time throughout th…

You might also likeclose