Search Result for " power steering system diagram pontiac grand prix 2001" :

Install Power Steering Pressure and/or Return Hose Assembly

39

Filed Under (Buick, Pontiac) by admin on 02-05-2013

ar assembly. Take away the power steering stress hose meeting from the vehicle. 6. Set up the ability steering pressure hose assembly to the vehicle. Join the power steering strain hose to the facility steering pump assembly. 7. Connect the facility steering stress hose to the power steering gear assembly.Tighten the ability steering pressure hose to the steering gear to 27 N·m (20 lb ft). 8. Install the bolt/screws to the retaining clips (three)…

1998 Buick Regal GS Pontiac Grand Prix GTP Fuel Pump Resistor Replacement

25

Filed Under (Buick, Pontiac) by admin on 04-03-2013

tion the interior fender splash protect to access the fuel pump resistor. 6. Remove the 2 bolts attaching the windshield washer reservoir to the rear mounting bracket and remove the one bolt attaching the bracket to the body. 7. From beneath the vehicle, using a 10mm box or open end wrench, take away the bolt that attaches the fuel pump resistor to the body. 8. Unclip the fuel pump resistor pigtail electrical (2-wire) connector from the sheet met…

1997 Buick Regal GS Pontiac Grand Prix GTP Fuel Pump Resistor Replacement

27

Filed Under (Buick, Pontiac) by admin on 22-03-2013

e car on a hoist. At the right front wheel opening, remove the three screws that connect the inside fender splash shield to the entrance fascia at the wheel opening and the 2 screws that attach it to the bottom of the fascia. 7. Reposition the internal fender splash shield to entry the fuel pump resistor. Unclip the fuel pump resistor electrical connector from the body and disconnect the connector. 8. Remove the 10mm hex head bolt attaching the f…

Toyota Steering Intermediate Shaft Noise Repair

26

Filed Under (Toyota) by admin on 17-12-2011

cm, 26 ftlbf) c. Set up the steering column hole cowl to the steering gap cowl boot. d. Join the clamp to the steering column gap cover boot and tighten the bolt. 6. Take away the steering wheel holder from the car (if used). 7. Road test the car to confirm the restore and make sure that the steering wheel is centered….

Ford Focus Steering Rack Installation Instructions

32

Filed Under (Ford) by admin on 19-02-2012

When you do your personal repairs and want to install a new steering rack for the 2000 to 2007 model years, comply with these instructions. Ford introduced the Focus with the 2000 model year and the primary era lasted for 7 years before the second generation was launched for the 2008 model year. The original shipped as a sedan, hatchback and wagon, but the hatchback and wagon failed in favor of a coupe with the 2008 manufacturing line. Ford Foc…

Ford Focus Power Steering Pump Installation Instructions

39

Filed Under (Ford) by admin on 30-04-2013

…f the pump, and drain the pump into the cup. 3. Take away the nuts which can be holding the pump onto the firewall, utilizing the wrench. Remove the belt on the pump from the pulley. Pull the old pump from the engine housing. 4. Secure the new pump onto the firewall with the securing nut. Exchange the belt to the pulley on the pump. Exchange the strains to the right holes on the pump. Tighten the nuts on the firewall and pump lines. Fill the pump…

2004-2005 Pontiac Grand Prix Plenum Water Deflector

32

Filed Under (Buick, Pontiac) by admin on 14-01-2012

tion. 2. Open the hood. 3. Take away the hood seal. 4. Take away the washer hose from the precise air inlet grille panel. 5. Remove the push pin that retains the air inlet grille panel. 6. Remove the air inlet grille panel. 7. Discard the rubber water deflector. 8. Install the new designed plenum water deflector. 9. Set up the air inlet grille panel. 10.Install the push pins. 11. Install the washer hose. 12. Install the hood seal. 13. Close the…

Buick Steering Wheel Installation Instructions

30

Filed Under (Buick) by admin on 29-03-2013

…eering column. Remove the steering wheel bolt and nut with a socket wrench and pull the old steering wheel off the steering column. 6. Place the new steering wheel onto the steering column and secure it with the nut and bolt. 7. Reattach the horn cap and its electrical connector as well as the steering wheel cover and its electrical connector. Secure the steering wheel cover by reinstalling the two Torx screws behind the steering wheel. Reconnect…

Ford Windstar Rack and Pinion Installation Instructions

35

Filed Under (Ford) by admin on 03-05-2013

…frame, which is subsequent to the steering rack. Use the jack to lift the subframe up to the physique till you may reattach the subframe bolts to the chassis. Torque the bolts to 85 foot-kilos with the 3/8-inch torque wrench. 4. Reinstall the exhaust flex tube to the exhaust using the 3/8-inch ratchet, extension and sockets. Set up the entrance wheels with the tire wrench. Reconnect the steering column to the rack and pinion utilizing the replace…

2000-2001 Infiniti G20 Lacks Power Due To Low Battery Voltage

39

Filed Under (Infiniti) by admin on 10-04-2013

ice Procedure 1. Carry out Self-Diagnosis using CONSULT-II to check for VHCL SPEED SEN-A/T and VHCL SPEED SEN- MTR trouble codes stored. 2. Use Nissan Battery/Starting/Charging System Tester (Kent-Moore device J-44373, Model 620) to test the automobile’s battery and charging system for correct battery voltage. NOTE: Discuss with bulletin number ITB99-036b, Infiniti Battery/Starting/Charging System Tester, for information about Kent-Moore i…

You might also likeclose