power steering system diagram on a 2002 chevy trailblazer

You search Auto repair manual PDF about power steering system diagram on a 2002 chevy trailblazer, search results will appear below. If search results do not exist, please search by others keyword.

Install Power Steering Pressure and/or Return Hose Assembly

39

Filed Under (Buick, Pontiac) by admin on 02-05-2013

eering strain hose to the facility steering pump assembly. 7. Connect the facility steering stress hose to the power steering gear assembly.Tighten the ability steering pressure hose to the steering gear to 27 N·m (20 lb ft). 8. Install the bolt/screws to the retaining clips (three). Tighten Tighten the retaining clip bolt/screws to 6 N·m (53 lb in). Set up the facility steering gear meeting heat protect (1). 9. Decrease the vehicle. Fill and ble…

Toyota Steering Intermediate Shaft Noise Repair

26

Filed Under (Toyota) by admin on 09-10-2014

cm, 26 ftlbf) c. Set up the steering column hole cowl to the steering gap cowl boot. d. Join the clamp to the steering column gap cover boot and tighten the bolt. 6. Take away the steering wheel holder from the car (if used). 7. Road test the car to confirm the restore and make sure that the steering wheel is centered….

Ford Focus Steering Rack Installation Instructions

32

Filed Under (Ford) by admin on 19-02-2012

fty nine foot pounds. Reattach the steering rack column coupler shaft and replace the unique flooring seal. Use pins to align the crossmember to chassis alignment holes and secure the crossmember with outer bolts tightened to 85 foot kilos and 4 interior bolts tightened to 148 foot pounds. 5. Take away the transmission jack and subframe alignment pins to reconnect the ability steering hoses. Tighten the hose assist clamp and change the heat shiel…

Ford Focus Power Steering Pump Installation Instructions

39

Filed Under (Ford) by admin on 30-04-2013

…f the pump, and drain the pump into the cup. 3. Take away the nuts which can be holding the pump onto the firewall, utilizing the wrench. Remove the belt on the pump from the pulley. Pull the old pump from the engine housing. 4. Secure the new pump onto the firewall with the securing nut. Exchange the belt to the pulley on the pump. Exchange the strains to the right holes on the pump. Tighten the nuts on the firewall and pump lines. Fill the pump…

Buick Steering Wheel Installation Instructions

30

Filed Under (Buick) by admin on 29-03-2013

…eering column. Remove the steering wheel bolt and nut with a socket wrench and pull the old steering wheel off the steering column. 6. Place the new steering wheel onto the steering column and secure it with the nut and bolt. 7. Reattach the horn cap and its electrical connector as well as the steering wheel cover and its electrical connector. Secure the steering wheel cover by reinstalling the two Torx screws behind the steering wheel. Reconnect…

Honda VFR Powerlet Steering Head Kit Installation

32

Filed Under (Honda) by admin on 29-04-2014

This easy to install, high quality, Powerlet™ Steering Head kit provides a convenient way to access the battery on Honda VFR motorcycles (1994-Present (Honda VFR750, Honda VFR800, Honda 800 VTEC)). The operator can supply power to the battery (i.e. battery charger), draw power from the battery (i.e. heated vest) using the Powerlet socket. 1. Take away the seat, battery cowl & left aspect fairing. 2. Take away unfavorable battery lead. Remo…

Ford Windstar Rack and Pinion Installation Instructions

35

Filed Under (Ford) by admin on 03-05-2013

…mounting bolts for the rack and pinion into the meeting, then raise it up into the frame by means of the motive force aspect fender well. Bolt it in place using the 3/8-inch ratchet wrench and socket, then torque the bolts to 85 foot-kilos with the 3/8-inch torque wrench. 2. Install the power steering traces onto the rack and pinion with an open-finish wrench. Bolt the heat protect in place with the 3/8-inch ratchet wrench. Install the tie rod en…

Ford F250 Gasoline Serpentine Belt Installation Instructions

22

Filed Under (Ford) by admin on 03-01-2012

…ine. 3. Connect the belt tensioner tool to the serpentine belt tensioner. Move the tensioner aside with the software and slip the serpentine belt over the tensioner pulley, per your F250′s specific belt-routing diagram. 4. Release the pressure on the tensioner with the software, then remove the device and shut the hood. Belt-routing diagrams range from mannequin year to mannequin 12 months and likewise by the F250′s specific accent se…

1998-2002 Honda Accord V6 Comptech Supercharger Kit

34

Filed Under (Honda) by admin on 05-03-2013

ive : With alternator pulley dealing with up take away inventory alternator pulley with a 22mm & 10mm wrench (an affect gun might must be used for removal). Install new alternator pulley (See Observe*) and tighten nut to 81.7 ft-lbs torque. 7. Alternator : Reinstall alternator in reverse order. Set up new metal alternator/blower bracket on prime of alternator utilizing manufacturing facility hardware. Torque to specs in Step 5. Substitute al…

Ford Super Duty Power Door Lock Actuator Installation Instructions

34

Filed Under (Ford) by admin on 31-10-2012

…ok the Super Duty’s new power lock actuator onto the lock rod by hand. Connect the power lock actuator to the door with the retaining bolt. Plug the lock wiring connector into the brand new power lock actuator manually. 6. Put the Super Duty’s door panel again on the truck door by reversing your removing steps….

You might also likeclose