Search Result for " power steering system diagram 2006 chevrolet trailblazer ls" :

Install Power Steering Pressure and/or Return Hose Assembly

39

Filed Under (Buick, Pontiac) by admin on 02-05-2013

ar assembly. Take away the power steering stress hose meeting from the vehicle. 6. Set up the ability steering pressure hose assembly to the vehicle. Join the power steering strain hose to the facility steering pump assembly. 7. Connect the facility steering stress hose to the power steering gear assembly.Tighten the ability steering pressure hose to the steering gear to 27 N·m (20 lb ft). 8. Install the bolt/screws to the retaining clips (three)…

Toyota Steering Intermediate Shaft Noise Repair

26

Filed Under (Toyota) by admin on 17-12-2011

cm, 26 ftlbf) c. Set up the steering column hole cowl to the steering gap cowl boot. d. Join the clamp to the steering column gap cover boot and tighten the bolt. 6. Take away the steering wheel holder from the car (if used). 7. Road test the car to confirm the restore and make sure that the steering wheel is centered….

Ford Focus Steering Rack Installation Instructions

32

Filed Under (Ford) by admin on 19-02-2012

When you do your personal repairs and want to install a new steering rack for the 2000 to 2007 model years, comply with these instructions. Ford introduced the Focus with the 2000 model year and the primary era lasted for 7 years before the second generation was launched for the 2008 model year. The original shipped as a sedan, hatchback and wagon, but the hatchback and wagon failed in favor of a coupe with the 2008 manufacturing line. Ford Foc…

Ford Focus Power Steering Pump Installation Instructions

39

Filed Under (Ford) by admin on 30-04-2013

…f the pump, and drain the pump into the cup. 3. Take away the nuts which can be holding the pump onto the firewall, utilizing the wrench. Remove the belt on the pump from the pulley. Pull the old pump from the engine housing. 4. Secure the new pump onto the firewall with the securing nut. Exchange the belt to the pulley on the pump. Exchange the strains to the right holes on the pump. Tighten the nuts on the firewall and pump lines. Fill the pump…

Buick Steering Wheel Installation Instructions

30

Filed Under (Buick) by admin on 29-03-2013

…eering column. Remove the steering wheel bolt and nut with a socket wrench and pull the old steering wheel off the steering column. 6. Place the new steering wheel onto the steering column and secure it with the nut and bolt. 7. Reattach the horn cap and its electrical connector as well as the steering wheel cover and its electrical connector. Secure the steering wheel cover by reinstalling the two Torx screws behind the steering wheel. Reconnect…

Ford Windstar Rack and Pinion Installation Instructions

35

Filed Under (Ford) by admin on 03-05-2013

…frame, which is subsequent to the steering rack. Use the jack to lift the subframe up to the physique till you may reattach the subframe bolts to the chassis. Torque the bolts to 85 foot-kilos with the 3/8-inch torque wrench. 4. Reinstall the exhaust flex tube to the exhaust using the 3/8-inch ratchet, extension and sockets. Set up the entrance wheels with the tire wrench. Reconnect the steering column to the rack and pinion utilizing the replace…

Honda VFR Powerlet Steering Head Kit Installation

32

Filed Under (Honda) by admin on 29-04-2014

motor. Observe the clutch hose out toward the underside of the Steering Head tube. Route the harness up into the Steering Head tube. Connect the black wire to the radiator mounting bolt or different chassis bolt in the area. 4. Set up the fuse in the fuse-holder. The middle terminal is plus and the outer ring is negative. Apply both dielectric grease or Vaseline to the spade terminals. Join the purple wire to the positive spade terminals &…

Ford F250 Gasoline Serpentine Belt Installation Instructions

22

Filed Under (Ford) by admin on 03-01-2012

…ine. 3. Connect the belt tensioner tool to the serpentine belt tensioner. Move the tensioner aside with the software and slip the serpentine belt over the tensioner pulley, per your F250′s specific belt-routing diagram. 4. Release the pressure on the tensioner with the software, then remove the device and shut the hood. Belt-routing diagrams range from mannequin year to mannequin 12 months and likewise by the F250′s specific accent se…

Loss of Communication with Brake Module (Reground EBCM Ground)

27

Filed Under (Cadillac, Chevrolet, GMC, Oldsmobile) by admin on 09-04-2013

hers and nuts specified in this bulletin. These parts have been identified because of their conductive finish. 4. Install a washer and nut to the back facet of the frame. Tighten Tighten the nut to 9 N·m (seventy nine lb in). 5. Cover the front and back aspect of the restore area using Rubberized Undercoating. An additional test may be made to ensure an excellent connection for the Battery Cable to Body ground. It’s potential for this groun…

Ford Super Duty Power Door Lock Actuator Installation Instructions

34

Filed Under (Ford) by admin on 31-10-2012

…ok the Super Duty’s new power lock actuator onto the lock rod by hand. Connect the power lock actuator to the door with the retaining bolt. Plug the lock wiring connector into the brand new power lock actuator manually. 6. Put the Super Duty’s door panel again on the truck door by reversing your removing steps….

You might also likeclose