Search Result for " pcv valve 2008 5 3" :

Ford Explorer EGR Valve Installation

31

Filed Under (Ford) by admin on 08-01-2012

…for the precise location of the valve but typically it is going to be on one of the sides of the engine block popping out from the consumption manifold. The vacuum hose will pull off the EGR valve. 3. In case your engine is a 4.6L, remove the nut and brake booster bracket that the valve passes through. On the 5.4L Ford engine, take away the nuts holding the DPFE Sensor together with your socket wrench and pull the sensor to 1 side. It is best to…

Ford EGR Valve Replacement Instructions

34

Filed Under (Ford) by admin on 27-04-2013

l mushroom, between 1 and a couple of inches in diameter. You’ll be able to determine the valve by the metal pipe linked between the exhaust manifold and the valve, which is seating on one aspect of the intake manifold. 4. Disconnect the vacuum hose or hoses from the top of the valve by hand. Also, unplug the electrical connector from the top of the valve if your explicit model is equipped with an digital or digital valve. 5. Remove the thr…

Honda Accord Valve Cover Gasket Installation Procedures

21

Filed Under (Honda) by admin on 15-06-2012

…ghout reassembly. It is made from aluminum, which could be very brittle and can crack easily. 1.Open the hood of the Honda Accord. 2. Take away the spark plug wire cover within the valve cover. Use the ratchet to drag out the 4 10 mm bolts holding it in place. 3. Use a spark plug wire puller to pull the spark plug wires out from the plugs. Tug at the base of the wire to keep away from damaging it. 4. Loosen the 10 mm bolts around the perimeter of…

Replace Evaporative Emission Vent Valve Solenoid – Page 1

22

Filed Under (Chevrolet, GMC) by admin on 14-12-2011

vent valve electrical connector, if equipped. 3. Disengage the two vent valve pipe clips securing the pipe to the underbody. Remove the clips from the underbody and discard.Disconnect the vent valve pipe at the EVAP canister. 4. Take away and retain the EVAP canister vent valve bracket mounting bolt. 5. Remove the entire EVAP canister vent valve meeting with bracket attached and discard. 6. Important: The new canister vent valve shall be put in i…

Toyota Camry EGR Valve Removal and Installation Instructions

40

Filed Under (Toyota) by admin on 23-02-2012

…Toyota Camry EGR Valve Removal Instructions 1. Disconnect and remove the EGR pipe and the 2 gaskets at every end. Use a ratchet, ratchet extension and socket. In case you have a 2.2-liter engine, skip this step and go to Step 4. 2. Remove the connector and clamp from the EGR gas temperature sensor. Use the ratchet and socket. 3. Remove the Evaporative Emissions (EVAP) management hose from the hook positioned on the EGR valve. 4. Unplug the vacuum…

Replace Evaporative Emission Vent Valve Solenoid – Page 2

29

Filed Under (Chevrolet, GMC) by admin on 16-04-2013

rid), 2007-2009 GMC Sierra Models (Excluding Hybrid). 1. Raise the vehicle. Suitably support the vehicle. 2. Disconnect the EVAP canister vent valve electrical connector. 3. Disconnect the canister pipe from the vent valve. 4. Push in the retainer and take away the present canister vent valve from the fuel tank clip or mounting bracket. Discard the old valve. 5. Reduce the present canister pipe approximately fifty one mm (2 in) to take away the…

2001 F-150 Intake Manifold 5.4L Removal Procedure

25

Filed Under (Ford) by admin on 15-11-2012

2001 Ford F-150 Intake Manifold 5.4L Removal Procedure : 1. Disconnect the battery ground cable (14301). 2. Relieve the fuel system pressure. 3. Drain the engine cooling system. 4. Take away the engine air cleaner (ACL)(9600) and the air cleaner outlet tube (9B659). 5. Compress and slide the hose clamp and disconnect the upper radiator hose. 6. Take away the accelerator cable snow shield. Remove the bolts. Remove the accelerator cable snow shiel…

2008-2010 F-Super Duty Diesel Engine Repeat Radiator Leaks

49

Filed Under (Ford) by admin on 29-04-2013

e check drive or potential for engine/vehicle injury, proceed to Step 5. b. Before driving the car confirm the coolant level is at minimal degree or above in the degas bottle. If required, add 50/50 combine to coolant bottle. 4. Check Drive – use an Built-in Diagnostic System (IDS) or equivalent and monitor Engine Oil Temperature (EOT) and Engine Coolant Temperature (ECT) Parameter Identifiers (PIDS). a. With EOT at 195 °F (ninety one °C) d…

2001 F-150 Intake Manifold 5.4L Installation Procedure

36

Filed Under (Ford) by admin on 17-01-2012

stic scraper only. Clean all the sealing surfaces. 2. If eliminated, install the water crossover. 3. Install the intake manifold. Place the new intake manifold gaskets. Place the upper intake manifold. Loosely set up 9 bolts. 4. NOTE: The thermostat housing bolts are tightened in sequence with the intake manifold bolts. Do not tighten the thermostat housing bolts throughout thermostat installation. Set up the water thermostat. 5. Tighten the 11 b…

Ford Escape Fuel Pump Removal and Installation Instructions

37

Filed Under (Ford) by admin on 03-02-2012

…2.0L Engine 1. Open the hood and remove the relay panel cowl contained in the engine compartment. 2. Look for the Fuel Pump relay. The marks inside the panel cowl will point out the right relay. 3. Remove the gas pump relay. 4. Begin the engine. The lack of gas will stall the engine and relieve the gasoline system pressure. 5. Exchange the Fuel Pump relay and turn off the ignition switch. Then go to the subsequent section. Relieve the Fuel Syste…

You might also likeclose