Filed Under (Ford) by admin on 20-02-2012
e Belt Removal Instructions 1. Park your Ford F150 on a safe place and open the hood. 2. Place a drain pan below the engine within the path of the upper radiator hose, where it connects with the radiator, in case you have the 7.3L engine model. Remove the radiator clamp using a Phillips screwdriver or ratchet and socket. Twist and pull the hose off the radiator fitting. Go to Step 6. 3. Take away the cooling fan mounting bolts using a ratchet and…
Filed Under (Ford) by admin on 20-02-2012
ensioner again, then slowly release the tensioner to regain stress on the belt. 6. Make certain the belt is seated appropriately on all pulleys and that the ribs on the belt are appropriately lined up with the pulley grooves. 7. Run the engine and observe to ensure appropriate installation….
Filed Under (Ford) by admin on 03-01-2012
…r pulley, per your F250′s specific belt-routing diagram. 4. Release the pressure on the tensioner with the software, then remove the device and shut the hood. Belt-routing diagrams range from mannequin year to mannequin 12 months and likewise by the F250′s specific accent setup. Don’t try to make use of any routing diagram unless you’re positive it’s the appropriate one for your F250. A very good components individual at any For…
Filed Under (Buick) by admin on 22-02-2012
…ssing the spring-loaded tensioner. Reinstall the motor mount and coolant overflow bottle, tightening the bolts securely. Begin the engine, and verify that the belt is routed correctly and sitting evenly in the pulley grooves. 5. Remove the jack and the wooden block before check-driving….
Filed Under (Peugeot) by admin on 22-02-2012
ollow the diagram to position the belt around the pulleys apart from the tensioner pulley. 5. Pull the tensioner pulley with a socket wrench. Place the belt around the pulley. Slowly release the tensioner to tighten the belt. 6. Start the automotive to observe the belt. The belt should transit smoothly across the pulleys….
Filed Under (Ford) by admin on 14-03-2013
…th a new one and safe it to the tension meeting utilizing the existing tension pulley retaining bolt by the center of the pulley. Tighten it to 30 foot-kilos of torque before securing the tension assembly again on the engine. 5. Safe the tension pulley assembly to the engine using the armature retaining bolt and tighten to 30 foot-kilos of torque. Pull the Ford Bronco’s serpentine belt over the strain pulley with the tension pulley still lo…
Filed Under (Ford) by admin on 15-04-2013
at belt to the mounting bolt holes close to the buckle. It will secure the seat belt assembly together. Place the plastic housing excessive mounting bolts, and safe it by attaching the screws with a Phillips-head screwdriver. 5. Once the work is completed, check the seat belt, by by pulling it out and inserting it into the seat belt connector, to make guantee that it connects correctly….
Filed Under (Ford) by admin on 13-11-2012
…Remove the two bolts within the alternator and take away the alternator. 3. Install the new alternator with the 2 bolts and loosely tighten them for the moment. Connect the electrical connectors on the rear of the alternator. 4. Put the belt on the alternator pulley. Pull the alternator again to apply stress to the v-belt and tighten the adjuster bolt to hold the alternator in place. Tighten both bolts, prime and bottom. If it is a serpentine bel…
Filed Under (Ford) by admin on 25-03-2013
. 5. Lift the F150 off the jack stands, using the floor jack. Move all 4 jack stands away from the truck. Decrease the F150 to the ground. 6. Repeat Steps 1 by means of 5 on the opposite aspect to install the proper Nerf bar. 7. Re-tighten all the Nerf bar mounting nuts when done. When tightening, torque the nuts till the lock washers flatten out, then flip the nut 1/2-turn further….
Filed Under (Honda) by admin on 02-07-2012
…ne bay. Full this step from the engine bay and not from beneath the vehicle. 5. Place the brand new belt into the engine bay and route the belt around all the pulleys besides the tensioner pulley. Use your diagram as a guide. 6. Get under the Honda V6 again, push up on the ratchet driver handle and secure the belt over the tensioner pulley….