Search Result for " how to repair a leaf spring" :

Ford Ranger Leaf Spring Removal and Installation Instructions

32

Filed Under (Ford) by admin on 25-04-2013

…surface. 2. Loosen the rear wheel lugs with a lug wrench on the facet that you will be working on first. 3. Lift that rear wheel utilizing a flooring jack and support it on a jack stand. 4. Take away the wheel/tire assembly. 5. Help the rear axle with a Hi-Lift jack or ground jack. 6. Remove the U-bolt nuts that safe the rear axle to the leaf spring. Use a wrench or ratchet, ratchet extension and socket. 7. Elevate the U-bolts and spring plate o…

Ford Ranger Leaf Spring Bushings Installation Instructions

33

Filed Under (Ford) by admin on 23-02-2012

…Do not tighten the nut yet. 4. Increase or lower the axle until the rear spring eye is centered within the leaf spring shackle. Set up a mounting bolt through the shackle and bushing, then install a nut on the mounting bolt. 5. Tighten the mounting bolts with a torque wrench to the manufacturer’s specifications. Mount the wheel on the wheel studs and connect the tire with the lug nuts. Tighten the lug nuts with a lug wrench. Repeat these s…

Honda Civic Coilover Springs Installation Procedures

27

Filed Under (Honda) by admin on 24-11-2012

…e elements, however some don’t. When disassembling the springs, a spring compressor needs to be used to safely hold the pressure of the springs. Assemble the brand new coilover springs using these elements if necessary. 5. Set up the new coilover springs in place of the outdated assembly. Reverse the steps and install all of the bolts that have been removed. The jack may be used under the management arm to boost the brand new coilovers into…

Ford Brakes Repair Installation Instructions

36

Filed Under (Ford) by admin on 18-04-2013

…;re making it simpler to remove the wheel when the car is off the ground—you solely want to “break” the lug nut loose, not loosen it so much in order that the wheel/tire become unstable. 2. If your Ford is a 5-speed, put the automobile in 1st gear. If it is automatic, then it will be in park. Be certain the emergency brake is on. 3. Jack the automotive off the ground utilizing the entrance jack level on your Ford. For example, o…

1997 Honda Civic Front Suspension Strut Replacement

30

Filed Under (Honda) by admin on 16-05-2012

the strut to the fork utilizing a 3/eight-inch ratchet and 14 mm socket. 4. Pop the hood and find the two 14 mm bolts on the strut tower that secure the strut to the car. Unbolt those bolts using the ratchet and 14 mm socket. 5. Unbolt the fork from the decrease control arm using a 17 mm open-finish wrench and a three/8-inch ratchet with 17 mm socket. Do not pull out the bolt yet. 6. Hold the strut with one hand and pull out the bolt that secures…

Idle Fluctuation and/or the MIL Is On With DTC P1129 and/or P0505 Page 1

31

Filed Under (Honda) by admin on 26-03-2013

hooting. Repair Procedure A 1. Connect the HDS to the car’s DLC. 2. Start the engine, and turn on the HDS. 3. When prompted, enter the VIN and the odometer reading. 4. From the System Choice Menu display, choose PGM-FI. 5. From the Mode Menu, select DATA LIST. 6. Scroll down the checklist to PSP SWITCH. Watch the studying in the Worth column. 7. Examine for a broken power steering pressure swap wire by wiggling the P/S stress change wire ha…

Honda Civic Coilover Springs Installation Instructions

39

Filed Under (Honda) by admin on 28-07-2014

ll of those parts, but some don’t. When disassembling the springs, a spring compressor must be used to securely maintain the pressure of the springs. Assemble the new coilover springs utilizing these parts if necessary. 5. Set up the brand new coilover springs in place of the outdated assembly. Reverse the steps and set up the entire bolts that were removed. The jack may be used below the control arm to boost the brand new coilovers into pl…

1998 Chevy Truck Evaporator Core Service and Repair Page 2

26

Filed Under (Chevrolet) by admin on 29-01-2012

ator case retaining screws. Tighten to 2.5 N.m (24 in lb). 3. Install the evaporator core meeting to the vehicle. 4. Install the bolts which retain the evaporator case to the bulkhead. Tighten the bolts to 4.5 N.m (40 lb in). 5. Install the condenser to the evaporator line fitting. Install the accumulator. 6. Install the evaporator case bolts and screws. Tighten to 2.5 N.m (24 In in). Set up the blower motor resistor. 7. Install the evaporator ca…

1998 Chevy Truck Evaporator Core Service and Repair Page 1

32

Filed Under (Chevrolet) by admin on 23-01-2012

rage compartment. 3. Disconnect the passenger facet SIR. Remove the lower proper instrument panel mounting bolt. 4. Take away the left and right entrance speaker grilles. Take away the center instrument panel sound insulator. 5. Remove the left side instrument panel sound insulator. Disconnect the park brake launch cable. 6. Remove the knee bolster. Remove the lower left instrument panel mounting bolt. 7. Remove the BCM. Disconnect the driving fo…

Toyota Steering Intermediate Shaft Noise Repair

26

Filed Under (Toyota) by admin on 17-12-2011

shaft sub-assembly. a. Align the match-mark with the one on the steering sliding yoke sub-assembly and the shaft assembly. b. Install the steering sliding yoke sub-meeting with the bolt. Torque: 35.3 Nm (360 kgfcm, 26 ftlbf) 5. Connect the intermediate shaft sub-assembly. a. Align the match-marks on the steering intermediate shaft sub-assembly and the steering gear assembly. b. Install the shaft sub-assembly with the bolt. Torque: 35.three Nm (3…

You might also likeclose