Filed Under (Ford) by admin on 16-11-2012
aining nut on the base of the wiper arm. 3. Pull the wiper arm off the pivot arm and wiper motor assembly. 4. Slide the brand new wiper arm onto the pivot arm and wiper motor assembly. 5. Thread and tighten the retaining nut. 6. Push the wiper arm back down against the windshield….
Filed Under (Ford) by admin on 20-02-2012
ankshaft clockwise with a socket and ratchet until the roller rocker arms strikes all the way down to open the valve then rises back as much as shut the valve. When the valve rocker is all the way up, rotate the crank another 90 degrees. This can be a tried and true approach of adjusting both pedestal- and stud-mounted rockers accurately. This process only takes an extra 5 minutes, but the roller rocker arms will all be correct. This methodology…
Filed Under (Buick) by admin on 21-02-2012
s. with a 1/4-inch torque wrench and socket. 2. Place the control module and wiper motor in their recess. Snap the electrical connector into place by hand. 3. Install the wiper control module mounting bolts and torque them to 89 inch-lbs. with a 1/four-inch torque wrench and socket. 4. Place the water deflector in position on the motor. Set up the retainer pin by hand. 5. Install the washer hoses onto their nipples on the wiper arms by hand. Set…
Filed Under (Ford) by admin on 25-04-2013
l the stereo meeting into the dashboard stereo mounting dock. Press firmly on the outside of the trim panel that accommodates the newly installed stereo unit to snap it again into place within the dash. Return to the battery. 7. Place the negative battery cable clamp across the damaging battery terminal. Tighten the bolt on the cable’s clamp with the wrench. Close the Taurus’ hood….
Filed Under (Ford) by admin on 01-11-2012
astic wire group binders into the leads of the harness. 8. Insert the new stereo into the sleeve until it snaps into place. The face of the aftermarket stereo can be degree with the trim of the dashboard stereo mounting dock. 9. Replace the grounding cable over the adverse lead put up and tighten the cable’s clamp with the wench….
Filed Under (Ford) by admin on 12-03-2013
…read and tighten the bolts to safe the wiper motor to the firewall. 3. Align the mounting gap on the pivot arm with the mounting gap on the wiper motor. 4. Thread the mounting bolt to connect the pivot arm to the wiper motor. 5. Join the electrical plug to the wiper motor….
Filed Under (Ford) by admin on 19-08-2012
rd pad into the caliper bracket. Remove the twine and discard, and then replace the caliper onto the caliper bracket and rotor. Tighten the caliper locating bolts to 25 foot-pounds. 8. Repeat the procedure for the other side. 9. Replace the wheels and tighten the lug nuts to 100 foot-pounds. Pump the brake pedal until it is firm. Top off the brake fluid in the master cylinder using only clean DOT brake fluid. Test drive the Taurus to ensure prope…
Filed Under (Ford) by admin on 19-02-2012
…he engine has cooled. If the extent dropped greater than 1 inch, add fluid. Restart the car with the heat operating and proceed this process till the level stabilizes and the engine is operating at normal working temperature. 9. Change the cap on the radiator, shut the engine off and shut the hood….
Filed Under (Ford) by admin on 06-02-2012
Pull the speaker out barely to access the wiring harness to the speakers. Unplug the wiring by pulling the harness clip. There will probably be a locking tab holding the harness in. Pull the tabs out to slide the harness out. 6. Pull the speaker out manually. Make sure the wiring harness is accessible for the brand new speaker. Installing the Speaker on Ford Taurus 1. Connect the wiring harness to the brand new speakers. The harness ought to simp…
Filed Under (Ford) by admin on 24-05-2013
…six-pin connector from the back of the Ford Taurus radio. 5. Join the manufacturing unit antenna plug to the back of the brand new radio marked for the antenna. 6. Connect the six-pin connector to the back of the radio unit. 7. Slide the radio into the dash until it locks into the dash….