Filed Under (Ford) by admin on 04-01-2012
rear edge of the door panel. 4. Pry around the bottom and aspect edges of the door panel with the panel tool. Elevate the panel off of the door and disconnect the wiring harness on the backside of the door. 5. Remove the four 7/32-inch screws from the edge of the speaker with a screwdriver. Pull the speaker out of the door and unplug the wiring harness connected to the back of it. Plug the wiring harness into the new speaker and check its operati…
Filed Under (Ford) by admin on 12-11-2012
…hand. 4. Insert the F-250 or F-350′s new door lock actuator into the door by hand. Hook the door lock and door latch rods to the actuator manually. Bolt the actuator to the F-250 or F-350′s door with a socket set. 5. Reinstall the F-250 or F-350′s door panel in reverse of the way you eliminated it….
Filed Under (Buick) by admin on 25-02-2012
and stand it up properly. Pull the studs in the upright vertical runners into their holes and set up the nuts and tighten. Set up the bolts within the window motor and plug the wiring harness connector into the window motor. 6. Hold the door panel shut sufficient to the door and connect the window switch. Turn the important thing on and lift the window regulator to the center of the access within the door the place it will be straightforward to…
Filed Under (Honda) by admin on 03-01-2014
joint between the door pores and skin and door frame — off the door edge between the 2 marks made in Step 5, using the seam cutter included with the edge guard kit. This gives a easy floor for the edge guard to set on. 7. Paint any areas where the paint peeled off whereas removing the sealant, using touch-up paint. Paint over the traces you made with the permanent marker, utilizing the touch-up paint. Allow the touch up paint to dry and cu…
Filed Under (Buick) by admin on 27-02-2012
…e unseated, after which pull it a pair inches away from the door frame. Attain behind and disconnect the door handle meeting from the door panel and disconnect any remaining wire harness connections. Take away the door panel. 7. Take away the three retaining nuts holding the aspect-view mirror to the door frame. Take away any insulation to access the nuts. Use an acceptable-sized nut driver to remove the nuts. 8. Pry the mirror away from the exte…
Filed Under (Toyota) by admin on 24-02-2012
mall pole into the clip of the upper portion of the new handle. Take a look at the handle to ensure the door latches and unlatches properly. Set up the three 10 millimeter bolts and tighten. Reattach the clear plastic lining. 4. Place the remaining portion of the door panel onto the six plastic clips on the outer portion of the panel. Pull it over the inside door lock. Make sure that the interior door opener can be positioned by way of the suppli…
Filed Under (Ford) by admin on 31-10-2012
…ok the Super Duty’s new power lock actuator onto the lock rod by hand. Connect the power lock actuator to the door with the retaining bolt. Plug the lock wiring connector into the brand new power lock actuator manually. 6. Put the Super Duty’s door panel again on the truck door by reversing your removing steps….
Filed Under (Ford) by admin on 05-11-2012
…ewdriver. 5. Reattach the door deal with cup, securing it by tightening the mounting screw with a Phillips screwdriver. Reattach the arm relaxation, securing it by tightening the mounting screws with the Phillips screwdriver. 6. Roll the window up and down to ensure that it is working properly….
Filed Under (Buick) by admin on 23-04-2013
…the 10mm screw located underneath the swap panel. 6. Pry across the edges of the door panel together with your panel software to loosen the retaining clips holding the door panel into place. Pull the door panel off the door. 7. Unscrew the 4 Torx T-15 screws securing the speaker in place. Pull the speaker out of the door and disconnect the wiring harness on the back. 8. Plug the brand new speaker into the harness. Place it within the door and sc…
Filed Under (Ford) by admin on 17-11-2012
eans of the door’s window opening, however, if it’s doable, it may be easier to push it up by means of the underside of the door after which back down into the regulator. Bolt the window in place on the regulator. 6. Substitute the water protect and audio system on the door. Reattach the total trim panel in reverse order of removal. Fit the weatherstrip back on the window opening….