how to install an exhaust system on a 2001 corolla

You search Auto repair manual PDF about how to install an exhaust system on a 2001 corolla, search results will appear below. If search results do not exist, please search by others keyword.

Toyota Corolla Exhaust Removal and Installation Instructions

30

Filed Under (Toyota) by admin on 04-03-2012

ew exhaust system features a replacement resonator. In this case, reduce the unique resonator piping one to a few inches in entrance of the weld melding the resonator assembly to the exhaust piping leading towards the engine. 7. Prepare to install the new exhaust. Toyota Corolla Exhaust Installation Instructions 1. Set up the entrance resonator assembly using the hardware and clamps provided by the new exhaust system after slipping it over the re…

Ford Diesel Exhaust System Installation Instructions

36

Filed Under (Ford) by admin on 12-01-2012

…to the subsequent junction. The beneficial torque for exhaust bands is approximately thirty kilos of pressure. This allows for a safe seal without and bending or harm of the piping which might result in a future exhaust leak. 8. Join the cat-back exhaust system to the present catalytic converters using the brand new flange end of the upgraded exhaust connecting to the present flange of the current catalytic converters. Replace any exhaust gasket…

Ford Powerstroke Diesel Turbocharger Installation Instructions

33

Filed Under (Ford) by admin on 27-10-2012

…rstroke diesel engine to get all of the efficiency and turbo energy that late model Powerstrokes enjoy right off the manufacturing facility floor. Ford Powerstroke Diesel Turbocharger Installation 1. Minimize the exhaust pipe 6 inches after the “Y” pipe meets up with the only exhaust pipe below the passenger compartment of the truck. Loosen and remove the four nuts that hold the exhaust flange together. Pull the “Y” pipe f…

Honda TRX 450 Exhaust System Installation Instructions

34

Filed Under (Honda) by admin on 29-04-2013

ear shock, etc. After getting maneuvered the pinnacle pipe to the desired place, gently and evenly snug down nuts. DO NOT over tighten the head pipe nuts. 8. Tighten the mid mount bolt on the mid pipe and the silencer bolts. 9. As soon as all nuts and bolts are tight, check the fit again to verify no a part of the exhaust pipe touches the body of the ATV. Re-adjust head pipe if necessary. 10. The carburetor will should be re-jetted. Dasa Racing…

Install Power Steering Pressure and/or Return Hose Assembly

39

Filed Under (Buick, Pontiac) by admin on 02-05-2013

he steering gear to 27 N·m (20 lb ft). 8. Install the bolt/screws to the retaining clips (three). Tighten Tighten the retaining clip bolt/screws to 6 N·m (53 lb in). Set up the facility steering gear meeting heat protect (1). 9. Decrease the vehicle. Fill and bleed the ability steering system utilizing, J 43485. Power Steering Pressure (Inlet) and Return (Outlet) Hose Replacement Procedure 1. Raise and suitably help the vehicle. 2. Drain the ab…

2001 Lincoln LS Intake Manifold Installation Procedure

25

Filed Under (Lincoln) by admin on 10-04-2013

ventilation tube. Connect the IAC valve and TPS electrical connectors. 7. Join the LH gasoline injector connectors and position the engine wiring harness. 8. Install the bracket. Set up the bracket and nuts. Set up the hose. 9. Install the bracket and the nut. 10. Set up the electrical connectors on the bracket. Set up the LH KS connector. Install the CHT sensor connector. 11. Connect the fuel line. Connect the vacuum connector to the gasoline s…

2001 F-Super Duty 250-550 Wheel Hub Installation Procedure

45

Filed Under (Ford) by admin on 05-05-2013

xle shaft. b. Set up the snap ring. 8. NOTE: Any time the hub lock is removed, a new O-ring seal should be installed. Failure to do so could cause a vacuum leak and loss of 4 wheel drive functions. Install a brand new O-ring. 9. Install the hub lock. a. Position the hub lock. b. Install the retainer ring. 10. Position the entrance disc brake rotor (1125) to the wheel hub (1104). Ensure that the wheel hub and the entrance disc brake rotor braking…

1998 Chevy Truck Evaporator Core Service and Repair Page 2

26

Filed Under (Chevrolet) by admin on 29-01-2012

2.5 N.m (24 In in). Set up the blower motor resistor. 7. Install the evaporator case warmth protect, if equipped. Set up the appropriate fender. 8. Join the electrical connector for the horn. Install the radio antenna cable. 9. Install the fitting wheelhouse panel. Install the front bumper. Install the proper front headlamp assembly. 10. Connect the electrical connectors to the grille mounted lamps. Install the heater hoses. 11. Install the cool…

2001 F-150 Intake Manifold 5.4L Installation Procedure

36

Filed Under (Ford) by admin on 17-01-2012

Use a plastic scraper only. Clean all the sealing surfaces. 2. If eliminated, install the water crossover. 3. Install the intake manifold. Place the new intake manifold gaskets. Place the upper intake manifold. Loosely set up 9 bolts. 4. NOTE: The thermostat housing bolts are tightened in sequence with the intake manifold bolts. Do not tighten the thermostat housing bolts throughout thermostat installation. Set up the water thermostat. 5. Tighten…

Toyota Corolla Fuel Filter Installation Instructions

26

Filed Under (Toyota) by admin on 23-02-2012

ch. 7. Press the vent line on its fitting until the lock snaps in place; then set up the fuel line and safe it with the clip; plug the fuel pump vapor stress sensor electrical connector and the fuel pump electrical connector. 8. Join the black, adverse battery cable and set up the fuel tank filler cap. Start the engine and test for leaks; then flip off the engine and set the fuel pump assembly service cowl in place. Set up the mounting screws or…

You might also likeclose