Search Result for " how to install 1998 pontiac grand prix power steering pump" :

Install Power Steering Pressure and/or Return Hose Assembly

39

Filed Under (Buick, Pontiac) by admin on 02-05-2013

he steering gear to 27 N·m (20 lb ft). 8. Install the bolt/screws to the retaining clips (three). Tighten Tighten the retaining clip bolt/screws to 6 N·m (53 lb in). Set up the facility steering gear meeting heat protect (1). 9. Decrease the vehicle. Fill and bleed the ability steering system utilizing, J 43485. Power Steering Pressure (Inlet) and Return (Outlet) Hose Replacement Procedure 1. Raise and suitably help the vehicle. 2. Drain the ab…

1998 Buick Regal GS Pontiac Grand Prix GTP Fuel Pump Resistor Replacement

25

Filed Under (Buick, Pontiac) by admin on 04-03-2013

(2-wire) connector from the sheet metallic subsequent to the battery and disconnect the connector. Pull the resistor wiring and connector down and out from below the vehicle. Discard the fuel pump resistor and mounting bolt. 9. Reinstall the windshield washer reservoir rear mounting bracket to the body and install the bolt. Tighten the bolt to 7 NJm (62 lb ft). Install the 2 bolts that attach the windshield washer reservoir to the rear mounting…

Ford Focus Power Steering Pump Installation Instructions

39

Filed Under (Ford) by admin on 30-04-2013

…f the pump, and drain the pump into the cup. 3. Take away the nuts which can be holding the pump onto the firewall, utilizing the wrench. Remove the belt on the pump from the pulley. Pull the old pump from the engine housing. 4. Secure the new pump onto the firewall with the securing nut. Exchange the belt to the pulley on the pump. Exchange the strains to the right holes on the pump. Tighten the nuts on the firewall and pump lines. Fill the pump

Ford F-150 Water Pump Removal and Installation Instructions

22

Filed Under (Ford) by admin on 15-11-2012

nterclockwise with a socket, socket extension and socket-wrench whereas the fan-drive belt is still installed. 7. Take away the fan-drive belt. 8. Take away the fan meeting together with the fan pulley, fan spacer and shroud. 9. Take away the alternator bracket, alternator pivot bolt and energy steering pump bracket from the water pump by turning the bolts counterclockwise with a socket and socket-wrench. 10. Remove all 14 bolts that join the wat…

1997 Buick Regal GS Pontiac Grand Prix GTP Fuel Pump Resistor Replacement

27

Filed Under (Buick, Pontiac) by admin on 22-03-2013

nnector that was related to the resistor via the opening in the sheet steel and into the engine compartment. When correctly routed, the connector needs to be getting into the engine compartment simply rearward of the battery. 9. Verify that the black conduit on the wiring harness is defending the wiring from any sharp edges in the sheet metal opening. Reposition the conduit and harness if necessary. 10. Reposition and align the inner fender splas…

Toyota Steering Intermediate Shaft Noise Repair

26

Filed Under (Toyota) by admin on 17-12-2011

cm, 26 ftlbf) c. Set up the steering column hole cowl to the steering gap cowl boot. d. Join the clamp to the steering column gap cover boot and tighten the bolt. 6. Take away the steering wheel holder from the car (if used). 7. Road test the car to confirm the restore and make sure that the steering wheel is centered….

Ford 390 Fuel Pump Installation Instructions

33

Filed Under (Ford) by admin on 15-11-2012

ace on the engine. 7. Apply gasket sealant to the remaining side of the brand new gas pump gasket. 8. Press the replacement fuel pump against the gasket, then install the pump’s two retaining bolts with a socket wrench. 9. Tighten the in-line nut on the tip of the steel outlet line onto the bottom of the gas pump. 10. Press the tip of the rubber inlet line onto the metallic nipple on the underside of the fuel pump, then tighten the lineR…

Ford Escape Fuel Pump Removal and Installation Instructions

37

Filed Under (Ford) by admin on 03-02-2012

…the half of-inch disconnect instrument quantity 310-D005 or equivalent. 8. Unplug the vapor gas line at the gas pump module by squeezing the side tabs at the finish of the fitting and pulling the line apart from the fitting. 9. Unscrew the fuel pump module from the gasoline tank using the fuel tank sender wrench quantity 310-069 or equivalent. 10. Remove the fuel pump module and O-ring seal from the fuel tank. Ford Escape Fuel Pump Installation…

Ford F-Series Water Pump Installation Instructions

26

Filed Under (Ford) by admin on 04-08-2012

Use the jack to elevate the Ford F-Series truck once again. Take off the underbody splash shield and lower radiator hose still related to the water pump. Launch the jack. 6. Take off the bolts on the water pump, which include 9 bolts and stud bolts. Clean the floor of the mount. Install the Water Pump 1. Prepare the brand new gasket onto the water pump. Instead of sealant, Ford recommends lubricating your gasket with coolant. Maintain the gasket…

Ford 7.3 Turbo Diesel Water Pump Installation Instructions

42

Filed Under (Ford) by admin on 20-02-2012

sor wiring plugs and move them aside. Take away the four bolts holding the higher coolant hose onto the water pump. Remove the clamp holding the heater hose onto the water pump and remove the hose. 4. Loosen and take away the 9 attaching bolts from the water pump and remove the water pump from the engine bay. Take away the coolant temperature sensor and the thermostat from the old water pump and install them onto the brand new water pump utilizin…

You might also likeclose