Filed Under (Ford) by admin on 11-11-2012
…the wiring teams from the Ford to a wiring harness adapter. Connect the wiring harness adapter to the stereo. The wiring harness leads will likely be marked to determine which connections go into which of the stereo outlets. 7. Connect the sign cable and switch-on lead (each offered in the amplifier wiring package) to the wiring harness adapter. Route the cables from inside the stereo dock, beneath the carpeting, to the rear cargo area of the Es…
Filed Under (Ford) by admin on 30-10-2012
…of the faceplate adapter. 4. Connect the leads of the wiring harness adapter to the retailers on the again of the aftermarket stereo/radio. Slide the aftermarket stereo into the opening offered by the Ford faceplate adapter. 5. Place the negative battery cable clamp across the detrimental lead put up of the Ford battery. Tighten the bolt on the clamp with the ten mm wrench so that the clamp can not move freely in regards to the lead post….
Filed Under (Ford) by admin on 19-12-2012
…tchet. You will have to carry the nuts with a wrench to keep them from turning as you tighten the bolts. Remove the spring compressor from the coil spring. Pull the stabilizer bar into place and tighten the nut with a wrench. 6. Plug within the ABS sensor if your automobile has antilock brakes. Attach the brake hose bracket to the strut and tighten the nut with a wrench. Set up the wheel on the Escape and tighten the lug nuts with the lug wrench….
Filed Under (Ford) by admin on 22-04-2013
…he screwdriver or ratchet and socket. 3. Attach the fuel traces to the fuel filter fittings. 4. Set up new lock tabs to the fittings to safe the fuel traces to the filter. 5. Decrease the vehicle. 6. Plug the fuel pump relay. 7. Connect the black, adverse battery cable utilizing the wrench. 8. Flip the ignition key to “On” but don’t start the vehicle. Make sure that there are no leaks on the filter connections. 9. Start the engi…
Filed Under (Ford) by admin on 21-03-2013
…ing retailers on the back of the Ford’s inventory stereo. 6. Plug the patch cables into the wiring harness adapter leads. Discover the diagram in the wiring harness adapter’s guide for proper connection locations. 7. Feed the patch cables via the again of the Ford’s stereo dock to the ground of the vehicle on the passenger’s side. Slide the factory stereo into the Ford’s stereo dock until it locks into place inside t…
Filed Under (Ford) by admin on 12-01-2014
…g harness adapter. Attach the wiring harness adapter results in the brand new stereo. Plug the antenna wire into the aftermarket stereo. 5. Put the brand new stereo into the faceplate adapter package till it snaps into place. 6. Replace the battery cable clamp onto the destructive lead publish and tighten it with the screwdriver….
Filed Under (Ford) by admin on 04-05-2013
…panel device to take away the panels within the door openings holding the Ford’s carpeting to the ground of the vehicle. Place the cables beneath the carpeting. Change the panels by hand with a medium quantity of force. 7. Exchange the Ford’s stereo into the stereo dock. Take away the DIN elimination tools. 8. Connect the patch cables to their outlets on the CD changer. 9. Reconnect the adverse battery cable to the negative lead put u…
Filed Under (Ford) by admin on 03-02-2012
…by hand. 4. Lift the carpet underneath the seat. 5. Detach the access door on the floor to reach gasoline pump module on the fuel tank. Use a Phillips screwdriver. 6. Unplug the electrical connectors on the fuel pump module. 7. Disconnect the gas pump module from the gas lines utilizing the half of-inch disconnect instrument quantity 310-D005 or equivalent. 8. Unplug the vapor gas line at the gas pump module by squeezing the side tabs at the fin…
Filed Under (Ford) by Doe on 16-05-2014
…th a socket set. 6. Pull out the Ford earlier energy window regulator and trade it with the model new one. Bolt the model new energy window regulator to the door help, window glass and energy window motor with the socket set. 7. Reinstall the Ford door panel in reverse of the best way you eradicated it. Peel the packing tape off the Ford window and door sooner than using the power window….
Filed Under (Ford) by Doe on 18-05-2014
the coolant reservoir hose from the fan shroud. 5. Loosen the fan clutch assembly with the particular fan clutch removing tools. Rotate the fan and clutch meeting slowly counterclockwise till they launch from the water pump. 6. Place all the assembly into the hole of the fan shroud got here out of. Take away the fan clips from the fan shroud, if it has any. Ford F-Series Water Pump Remove Procedures 1. Raise the Ford F-Series truck with a jack,…