Search Result for " diagram rear wheel bearing assembly 2001 ford focus" :

2001 Expedition/Navigator Wheel Hub and Bearing Installation

25

Filed Under (Ford, Lincoln) by admin on 17-01-2012

equal assembly Ford specification ESA-M1C75-B. 4. Utilizing a bearing packer, pack the bearing cone and curler with wheel bearing grease. 5. Install the internal entrance wheel bearing. 6. Set up a new wheel hub grease seal. 7. Apply a light-weight coat of grease on the entrance wheel spindle. Use Premium Long-Life Grease XG-1-C or -Ok or equivalent assembly Ford specification ESA-M1C75-B. 8. CAUTION: Keep the brake disc centered on the front wh…

2000 F-150 Rear Wheel Bearing and Axle Shaft Oil Seal

33

Filed Under (Ford) by admin on 13-01-2012

and axle shaft for put on or damage. 4. If crucial, using the special tools, remove the rear wheel bearing. Rear Wheel Bearing and Axle Shaft Oil Seal Installation Procedure 1. Lubricate the new rear axle bearing. ? Use SAE 75W-140 High Efficiency Rear Axle Lubricant F1TZ-19580-B or equal assembly Ford specification WSL-M2C192-A. 2. Using the special instruments, install the rear bearing. 3. Lubricate the lip of the new bearing oil seal. ? Use…

Install Power Steering Pressure and/or Return Hose Assembly

39

Filed Under (Buick, Pontiac) by admin on 02-05-2013

ar assembly. Take away the power steering stress hose meeting from the vehicle. 6. Set up the ability steering pressure hose assembly to the vehicle. Join the power steering strain hose to the facility steering pump assembly. 7. Connect the facility steering stress hose to the power steering gear assembly.Tighten the ability steering pressure hose to the steering gear to 27 N·m (20 lb ft). 8. Install the bolt/screws to the retaining clips (three)…

Honda TRX 400EX Wheel Hub Installation

37

Filed Under (Honda) by admin on 12-02-2012

in your new hubs and be sure to use medium energy Loctite on the threads. 6. Apply a light-weight film of grease or oil to the large diameter of the spindle stud. Set up the brand new o-ringed bearing spacer onto the spindle. 7. Apply a thin film of grease to the seal surface on the bearing spacer and the inside diameter of the seal to prevent the seal from working dry. Set up the wheel hub onto the spindle and slide the outer bearing over the sp…

2001 Expedition/Navigator Wheel Hub and Bearing Removal

23

Filed Under (Ford, Lincoln) by admin on 11-11-2012

er nut. Remove the hub grease cap. Take away and discard the cotter pin. Remove the retainer nut. 5. Take away the spindle nut. 6. Remove the front wheel outer bearing retainer washer (1195) and the outer front wheel bearing. 7. Take away the brake disc and hub (1102). 8. Take away the internal entrance wheel bearing. Take away and discard the wheel hub grease seal (1190). Remove the inside front wheel bearing. 9. Utilizing a drift, remove the be…

Ford Focus Brake Pads Installation Instructions

34

Filed Under (Ford) by admin on 01-02-2012

f the brake caliper and take the previous Brake Pads out of the caliper by hand. Spray the within of the caliper with brake clear to remove any brake dust after which lubricate the caliper slide with the white lithium grease. 7. Retract the brake caliper piston with the caliper piston tool (you can purchase a caliper piston device at your native auto parts store). 8. Insert the brand new brake pads, in the identical route and orientation as the p…

Ford Focus Amplifier Installation Instruction

28

Filed Under (Ford) by admin on 21-03-2013

…ing retailers on the back of the Ford’s inventory stereo. 6. Plug the patch cables into the wiring harness adapter leads. Discover the diagram in the wiring harness adapter’s guide for proper connection locations. 7. Feed the patch cables via the again of the Ford’s stereo dock to the ground of the vehicle on the passenger’s side. Slide the factory stereo into the Ford’s stereo dock until it locks into place inside t…

2001 F-Super Duty 250-550 Wheel Hub Installation Procedure

45

Filed Under (Ford) by admin on 05-05-2013

equipped with ABS 6. NOTE: The next step applies only to automobiles geared up with ABS. Join the ABS sensor harness. a. Place the ABS sensor harness and install the routing clips. b. Join the harness connector. All vehicles 7. n-metallic thrust washer should be put in between the two steel thrust washers. Failure to take action will trigger extreme put on to the non-metallic thrust washer, allowing the axle shaft to travel additional in and out…

Buick Steering Wheel Installation Instructions

30

Filed Under (Buick) by admin on 29-03-2013

…eering column. Remove the steering wheel bolt and nut with a socket wrench and pull the old steering wheel off the steering column. 6. Place the new steering wheel onto the steering column and secure it with the nut and bolt. 7. Reattach the horn cap and its electrical connector as well as the steering wheel cover and its electrical connector. Secure the steering wheel cover by reinstalling the two Torx screws behind the steering wheel. Reconnect…

Ford Focus Fuel Tank Installation Instructions

20

Filed Under (Ford) by admin on 08-03-2013

…hten the rear wheel nuts with a torque wrench as a lot as doable or until the wheel nuts can’t flip any further. Refill your fuel tank with the gas out of your fuel container and then join the destructive battery cable. 7. Restore stress to your tank by putting on the fuel filler cap. Verify your automobile for any leaks or free wiring. If you don’t see anything, take a drive to check how it runs with the brand new fuel tank….

You might also likeclose