Search Result for " diagram for a oldsmobile intrigue 01 power steering line" :

Install Power Steering Pressure and/or Return Hose Assembly

39

Filed Under (Buick, Pontiac) by admin on 02-05-2013

eering strain hose to the facility steering pump assembly. 7. Connect the facility steering stress hose to the power steering gear assembly.Tighten the ability steering pressure hose to the steering gear to 27 N·m (20 lb ft). 8. Install the bolt/screws to the retaining clips (three). Tighten Tighten the retaining clip bolt/screws to 6 N·m (53 lb in). Set up the facility steering gear meeting heat protect (1). 9. Decrease the vehicle. Fill and ble…

Ford Focus Steering Rack Installation Instructions

32

Filed Under (Ford) by admin on 19-02-2012

fty nine foot pounds. Reattach the steering rack column coupler shaft and replace the unique flooring seal. Use pins to align the crossmember to chassis alignment holes and secure the crossmember with outer bolts tightened to 85 foot kilos and 4 interior bolts tightened to 148 foot pounds. 5. Take away the transmission jack and subframe alignment pins to reconnect the ability steering hoses. Tighten the hose assist clamp and change the heat shiel…

Ford Focus Power Steering Pump Installation Instructions

39

Filed Under (Ford) by admin on 30-04-2013

…f the pump, and drain the pump into the cup. 3. Take away the nuts which can be holding the pump onto the firewall, utilizing the wrench. Remove the belt on the pump from the pulley. Pull the old pump from the engine housing. 4. Secure the new pump onto the firewall with the securing nut. Exchange the belt to the pulley on the pump. Exchange the strains to the right holes on the pump. Tighten the nuts on the firewall and pump lines. Fill the pump…

Toyota Steering Intermediate Shaft Noise Repair

26

Filed Under (Toyota) by admin on 09-10-2014

cm, 26 ftlbf) c. Set up the steering column hole cowl to the steering gap cowl boot. d. Join the clamp to the steering column gap cover boot and tighten the bolt. 6. Take away the steering wheel holder from the car (if used). 7. Road test the car to confirm the restore and make sure that the steering wheel is centered….

Buick Steering Wheel Installation Instructions

30

Filed Under (Buick) by admin on 29-03-2013

…eering column. Remove the steering wheel bolt and nut with a socket wrench and pull the old steering wheel off the steering column. 6. Place the new steering wheel onto the steering column and secure it with the nut and bolt. 7. Reattach the horn cap and its electrical connector as well as the steering wheel cover and its electrical connector. Secure the steering wheel cover by reinstalling the two Torx screws behind the steering wheel. Reconnect…

Ford Windstar Rack and Pinion Installation Instructions

35

Filed Under (Ford) by admin on 03-05-2013

…mounting bolts for the rack and pinion into the meeting, then raise it up into the frame by means of the motive force aspect fender well. Bolt it in place using the 3/8-inch ratchet wrench and socket, then torque the bolts to 85 foot-kilos with the 3/8-inch torque wrench. 2. Install the power steering traces onto the rack and pinion with an open-finish wrench. Bolt the heat protect in place with the 3/8-inch ratchet wrench. Install the tie rod en…

Ford Radiator Removal and Installation Instructions

28

Filed Under (Ford) by admin on 10-01-2012

…cooler line from the radiator. Use a flare wrench. Then cover the line with a plastic bag to keep away from contamination of oil cooler system. 7. Unscrew the two A/C condenser mounting bolts, utilizing a ratchet and socket. 8. Jack up the entrance of your Ford automobile, utilizing a ground jack, and safely assist it on two jack stands. 9. Take away the radiator support brackets, using a ratchet and socket. 10. Disconnect the decrease radiator…

Honda VFR Powerlet Steering Head Kit Installation

32

Filed Under (Honda) by admin on 29-04-2014

This easy to install, high quality, Powerlet™ Steering Head kit provides a convenient way to access the battery on Honda VFR motorcycles (1994-Present (Honda VFR750, Honda VFR800, Honda 800 VTEC)). The operator can supply power to the battery (i.e. battery charger), draw power from the battery (i.e. heated vest) using the Powerlet socket. 1. Take away the seat, battery cowl & left aspect fairing. 2. Take away unfavorable battery lead. Remo…

Ford Super Duty Power Door Lock Actuator Installation Instructions

34

Filed Under (Ford) by admin on 31-10-2012

…ok the Super Duty’s new power lock actuator onto the lock rod by hand. Connect the power lock actuator to the door with the retaining bolt. Plug the lock wiring connector into the brand new power lock actuator manually. 6. Put the Super Duty’s door panel again on the truck door by reversing your removing steps….

1998-2002 Honda Accord V6 Comptech Supercharger Kit – Page 2

34

Filed Under (Honda) by admin on 05-03-2013

re against the bracket to distort plate or push it out, this spacer is only designed to take up inconsistencies in factory head. Whereas holding spacer with a 19mm wrench, insert supplied 10mm bolt into gap and torque bolt to 28ft-lbs. Torque cam seal bolts (B) to 15ft/lbs. Change EGR valve, utilizing provided gasket, and torque to 15ft/lbs. Substitute electrical plug. 12. Blower preparation : Blower has (6) bolts around enter shaft. Lower (4) bo…

You might also likeclose