Filed Under (Buick, Pontiac) by admin on 02-05-2013
ar assembly. Take away the power steering stress hose meeting from the vehicle. 6. Set up the ability steering pressure hose assembly to the vehicle. Join the power steering strain hose to the facility steering pump assembly. 7. Connect the facility steering stress hose to the power steering gear assembly.Tighten the ability steering pressure hose to the steering gear to 27 N·m (20 lb ft). 8. Install the bolt/screws to the retaining clips (three)…
Filed Under (Ford) by admin on 30-04-2013
…f the pump, and drain the pump into the cup. 3. Take away the nuts which can be holding the pump onto the firewall, utilizing the wrench. Remove the belt on the pump from the pulley. Pull the old pump from the engine housing. 4. Secure the new pump onto the firewall with the securing nut. Exchange the belt to the pulley on the pump. Exchange the strains to the right holes on the pump. Tighten the nuts on the firewall and pump lines. Fill the pump…
Filed Under (Ford) by admin on 21-11-2012
…ocket set. 6. Pull out the Ford’s outdated power window regulator and exchange it with the new one. Bolt the brand new power window regulator to the door assist, window glass and power windows motor with the socket set. 7. Reinstall the Ford’s door panel in reverse of how you eliminated it. Peel the packing tape off the Ford’s power windows and door before using the facility window….
Filed Under (Ford) by admin on 26-10-2012
ke away the window motor and regulator to make means for the new parts. 6. Set up the brand new power window regulator. Place the brand new window motor and regulator in place, and exchange the screws that held them in place. 7. Exchange the window glass, and connect it to the power window motor and regulator assembly. Again, it’s possible you’ll need to have a buddy assist you in the course of so you don’t damage your window gl…
Filed Under (Ford) by admin on 19-02-2012
When you do your personal repairs and want to install a new steering rack for the 2000 to 2007 model years, comply with these instructions. Ford introduced the Focus with the 2000 model year and the primary era lasted for 7 years before the second generation was launched for the 2008 model year. The original shipped as a sedan, hatchback and wagon, but the hatchback and wagon failed in favor of a coupe with the 2008 manufacturing line. Ford Foc…
Filed Under (Ford) by admin on 31-10-2012
…ok the Super Duty’s new power lock actuator onto the lock rod by hand. Connect the power lock actuator to the door with the retaining bolt. Plug the lock wiring connector into the brand new power lock actuator manually. 6. Put the Super Duty’s door panel again on the truck door by reversing your removing steps….
Filed Under (Ford) by admin on 20-02-2012
ensioner again, then slowly release the tensioner to regain stress on the belt. 6. Make certain the belt is seated appropriately on all pulleys and that the ribs on the belt are appropriately lined up with the pulley grooves. 7. Run the engine and observe to ensure appropriate installation….
Filed Under (Ford) by admin on 01-11-2012
ires. 6. Slide the installation sleeve from the Ford stereo equipment into the empty stereo mounting dock. Fold the tabs on the sleeve around the stereo mounting dock edges, securing the sleeve contained in the mounting dock. 7. Join the stereo wiring from the dock to a wiring harness adapter. Plug the plastic wire group binders into the leads of the harness. 8. Insert the new stereo into the sleeve until it snaps into place. The face of the afte…
Filed Under (Ford) by admin on 25-04-2013
l the stereo meeting into the dashboard stereo mounting dock. Press firmly on the outside of the trim panel that accommodates the newly installed stereo unit to snap it again into place within the dash. Return to the battery. 7. Place the negative battery cable clamp across the damaging battery terminal. Tighten the bolt on the cable’s clamp with the wrench. Close the Taurus’ hood….
Filed Under (Toyota) by admin on 09-10-2014
cm, 26 ftlbf) c. Set up the steering column hole cowl to the steering gap cowl boot. d. Join the clamp to the steering column gap cover boot and tighten the bolt. 6. Take away the steering wheel holder from the car (if used). 7. Road test the car to confirm the restore and make sure that the steering wheel is centered….