Search Result for " 2013 f150 speaker wire color code" :

Ford SuperCrew Amplifier Installation Instructions

29

Filed Under (Ford) by admin on 07-03-2013

…reach the amplifier to the exposed wire coming off the deck. Remember you will have a positive and negative wire to connect. Wrap the connections you just made with electrical tape to assure the wires won’t come apart. 5. Run the end of the speaker wire from the back of the deck to the High Level inputs on the amplifier. Slide the end of the wires into the inputs like you are hooking up speakers to the amplifier. Turn the screw until the w…

Ford Focus Car Speaker System Installation Instructions

41

Filed Under (Ford) by admin on 02-04-2013

…sed with the door panel screws. Cut the ends of the speaker wires off with pliers and disconnect the speaker. Use a pair of wire splitters and split the wire so that there’s sufficient to connect with your new speakers. 5. Twist the speaker wire coming from the within of the door to the wire of the brand new speakers. Ensure it is tight. Wrap electrical tape around the uncovered wire to secure the connection. 6. Reconnect the battery and te…

Ford Taurus Speaker Removal and Installation Instructions

27

Filed Under (Ford) by admin on 06-02-2012

the speaker cowl with a flathead screwdriver. The quilt will come out, exposing the outdated speaker. 4. Unscrew the hardware holding the speaker in place. There shall be four Phillips head screws centered around the speaker. 5. Pull the speaker out barely to access the wiring harness to the speakers. Unplug the wiring by pulling the harness clip. There will probably be a locking tab holding the harness in. Pull the tabs out to slide the harness…

Ford Ranger Speaker Installation Instructions

31

Filed Under (Ford) by admin on 07-02-2012

Most Ford Ranger pick-ups come geared up with two pairs of 6 x 8-inch speakers, one in every front door, and a pair situated in the rear panels on the rear of the interior compartment. Although 6 x 8 inches is the official Speaker dimension, most 5 x 7-inch speakers will match in the manufacturing unit gap with no modification required. Many Ranger owners prefer to interchange the manufacturing unit audio system with 6.5-inch round speakers to i…

Ford F150 Super Crew Cab Nerf Bars Installation Instructions

34

Filed Under (Ford) by admin on 25-03-2013

17;s frame. Note that some Nerf bars could include a rubber insulator to take a seat between the mounting bracket and frame; if yours do, make sure that to put the insulator between the bar and body before inserting the bolt. 5. Lift the F150 off the jack stands, using the floor jack. Move all 4 jack stands away from the truck. Decrease the F150 to the ground. 6. Repeat Steps 1 by means of 5 on the opposite aspect to install the proper Nerf bar….

Honda Civic Remote Starter Installation Instructions

34

Filed Under (Honda) by admin on 20-03-2012

…a skinny coat of rubber cement. 4. Bolt the hood pin from the remote starter package to the plastic clamp near the Civic’s hood latch. Use the 6-inch metal bolts and the adjustable wrench to safe the hood pin in place. 5. Unwind the wire hanger and connect some electrical tape to the end. Use the hanger to push the gray wire (the ability wire) from the starter by means of the warmth duct and into the engine area of the Civic. 6. Pull the g…

Ford Escape Speaker Installation Instructions

41

Filed Under (Ford) by admin on 04-01-2012

…ead screw from the rear edge of the door panel. 4. Pry around the bottom and aspect edges of the door panel with the panel tool. Elevate the panel off of the door and disconnect the wiring harness on the backside of the door. 5. Remove the four 7/32-inch screws from the edge of the speaker with a screwdriver. Pull the speaker out of the door and unplug the wiring harness connected to the back of it. Plug the wiring harness into the new speaker an…

Toyota Camry Sirius Car Radio Installation Instructions

36

Filed Under (Toyota) by admin on 23-02-2012

knife or credit card to pry the molding around the rear windshield to allow space for the wire. Place the wire in the space provided horizontally then vertically until you have reached the Camry’s trunk. Open the trunk. 5. Feed the antenna wire under the weather stripping lining the trunk’s opening. 6. Feed the antenna wire along the path of the Camry’s rear speaker wiring harness to the front of the vehicle just beneath the cen…

Honda Odyssey Trailer Wiring Installation Instructions

32

Filed Under (Honda) by admin on 26-02-2012

sent wires. 4. Find the top of the brand new wire outdoors the Odyssey by reaching up between the bumper and the splash guard. Pull the wire by the grommet until there is enough length outside to succeed in the trailer hitch. 5. Route a 10-gauge black wire from the constructive terminal of the battery down by way of the engine bay and along a chassis frame rail to the location of the trailer hitch. Use a plastic zip tie roughly every foot to secu…

Ford Ranger CB Radio Installation Instructions

49

Filed Under (Ford) by admin on 19-02-2012

…ave 1/2 inch of insulation off the tip of the bottom wire using electrician’s pliers. 3. Slide a hoop crimp terminal onto the naked portion of the ground wire. 4. Crimp the terminal utilizing electrician’s pliers. 5. Lay the ring terminal towards a bare portion of the car’s body. The terminal should be against metal. 6. Secure the ring terminal to the car’s body by screwing a self-drilling, self-tapping screw by means of t…

You might also likeclose