Search Result for " 2012 px ford ranger workshop manual" :

Ford Ranger Skid Plate Installation Instructions

33

Filed Under (Ford) by admin on 05-04-2013

ing hardware supplied with the skid plate. 4. Take away the jack stands from underneath the Ranger’s engine. Elevate the Ranger off the opposite two jack stands. Move the stands apart and lower the Ranger to the ground. 5. Transfer the wheel chocks away from the Ranger’s again tire before driving….

1999 Ford Ranger Extended Cabs Westin Nerf Bars Installation Instructions

35

Filed Under (Ford) by admin on 26-06-2012

ghten the nuts onto the bolts with a socket set. 4. Move the jack stands to the best side of the 1999 Ford Ranger and repeat the primary three steps to install the precise Westin Nerf Bar. Take away the jack stands when done. 5. Use care when setting the Nerf Bars on the jack stands so you do not mar the Nerf Bars’ end on the rough heads of the stands….

Ford Ranger Body Lift Kit Installation Instructions

31

Filed Under (Ford) by admin on 19-02-2012

…body lift pucks onto the manufacturing unit bushings. 4. Slide the body lift pucks into position on prime of the factory bushings. Do not remove the factory bushings. Lower the vehicle body onto the newly put in carry pucks. 5. Install the new bolts into place and tighten them utilizing a ratchet and socket. Confirm that all six bolts are tight. Re-set up the bumper, fan, and shroud utilizing a socket and ratchet. Ford Ranger Bed Portion of the…

Ford Ranger Clutch Removal and Installation Instructions

36

Filed Under (Ford) by admin on 28-04-2013

Take away the interior elements–the elements under the hood. This consists of the starter, which is attached to the transmission bell-housing. 4. Disconnect the drive-shaft and the hose for the hydraulic slave cylinder. 5. Use a jack to raise one side of your truck. 6. Utilizing a metric socket set, undo the transmission cross-member and bolts, which is able to help you remove the transmission from your Ranger. 7. Take away the strain plate…

Ford Ranger Tow Bar Installation Instructions

31

Filed Under (Ford) by admin on 17-11-2012

cle body the place the bolt holes shall be drilled. These marks should be centered on the body based on the widths of the frame and tow bar. 4. Clamp the tow bar to the car frame and align the bar to your drill hole markings. 5. Drill the holes in the body, using the position of the tow bar as a template. 6. Insert the mounting bolts and tighten them with a wrench. 7. Connect the safety cable and security chains; these must be included with the t…

Ford Ranger Stereo/Radio Installation Instructions

34

Filed Under (Ford) by admin on 13-02-2012

…8217;s face to receive the tools. 3. Pull the instruments outward and then pull the radio away from the dashboard. 4. Disconnect the white plastic wire binders from the rear of the radio. Pull the antenna cable from the unit. 5. Insert the Ford set up kit dock to receive the aftermarket radio. Feed the Ranger’s wiring by way of the back of the kit. Join the plastic wire binders to the wiring harness adapter. Join the wiring harness adapter…

Ford Ranger Front and Rear Shock Replacement Instructions

30

Filed Under (Ford) by admin on 20-02-2012

The shocks on your Ford Ranger should be replaced in 50,000-mile intervals. Shocks help within the total high quality of the trip, and worn shocks can cause a lot of problems: poor dealing with, elevated tire put on and a tough ride. If your Ranger reveals any of those signs, you would possibly want to switch its shocks. New shocks may be bought out of your native auto components store and installed yourself with easy tools. Ford Ranger Front Sh…

Ford Ranger Door Lock Removal and Installation Instruction

43

Filed Under (Ford) by admin on 05-11-2012

…ush outward to launch the plastic retainer clips. Pop the clips out one at a time to reduce harm to them. 4. Pull the door panel off and set it apart away from the work area. Unhook the door latch rod from the retaining clip. 5. Slide the lock cylinder retainer away from the lock cylinder using a pair of pliers. Pull out the Door Lock cylinder. Installing in the Door Lock 1. Insert the brand new lock cylinder into the lock cylinder gap from the s…

Ford Ranger Starter Motor Installation Instructions

29

Filed Under (Ford) by admin on 01-05-2013

…the physique of the starter with one hand when you take away the 2 starter-mounting bolts with the socket set utilizing your different hand. Do not let the starter rest on the loose bolts at any time throughout this process. 5. Set the old starter off to the facet and hold the replacement starter in position. Thread the mounting bolts back in by hand after which tighten them down with the socket set. Once again, don’t let the starter’…

Ford Ranger Leaf Spring Removal and Installation Instructions

32

Filed Under (Ford) by admin on 25-04-2013

surface. 2. Loosen the rear wheel lugs with a lug wrench on the facet that you will be working on first. 3. Lift that rear wheel utilizing a flooring jack and support it on a jack stand. 4. Take away the wheel/tire assembly. 5. Help the rear axle with a Hi-Lift jack or ground jack. 6. Remove the U-bolt nuts that safe the rear axle to the leaf spring. Use a wrench or ratchet, ratchet extension and socket. 7. Elevate the U-bolts and spring plate o…

You might also likeclose