Search Result for " 2006 pontiac pursuit crank sensor install" :

Buick Crankshaft Sensor Replacement Instructions

43

Filed Under (Buick) by admin on 24-11-2012

ep 7 for reference, and continue with Steps three to 7 if necessary. 3. Loosen the front passenger-side wheel lugs using a lug wrench. 4. Increase the entrance of your Buick using a floor jack, and help it on two jack stands. 5. Finish removing the wheel lugs from the entrance passenger facet wheel using the lug wrench; then take the wheel/tire assembly off the wheel hub and set it aside. 6. Remove the splash protect cover using the ratchet and s…

Install Power Steering Pressure and/or Return Hose Assembly

39

Filed Under (Buick, Pontiac) by admin on 02-05-2013

ability steering fluid. 3. Remove the ability steering gear assembly warmth shield. 4. Disconnect the facility steering stress hose from the facility steering pump assembly. Take away the bolt/screws from the retaining clips. 5. Disconnect the ability steering strain hose from the ability steering gear assembly. Take away the power steering stress hose meeting from the vehicle. 6. Set up the ability steering pressure hose assembly to the vehicle….

2001 Lincoln LS Intake Manifold Installation Procedure

25

Filed Under (Lincoln) by admin on 10-04-2013

the bolts within the sequence shown. 3. Set up the Delta PFE sensor. Install the sensor and the bolts. Join the electrical connector. Connect the hoses. 4. Connect the RH fuel injectors and position the engine wiring harness. 5. Connect the hoses (1) and install the hose within the clip (2). 6. Connect the crankcase ventilation tube. Connect the IAC valve and TPS electrical connectors. 7. Join the LH gasoline injector connectors and position the…

Buick LeSabre Crankshaft Position Sensor Installation Instructions

25

Filed Under (Buick) by admin on 21-02-2012

e tool. If there is no such thing as a contact after tightening, withdraw the sensor from the tool and mount the sensor pedestal to the block with the 2 bolts. Tighten the bolts. Plug within the electrical plug on the sensor. 5. Install the harmonic balancer and tighten the center bolt to a hundred and eighty foot pounds of torque. Install the splash defend and wheel in reverse order of removal….

2001 F-Super Duty 250-550 Wheel Hub Installation Procedure

45

Filed Under (Ford) by admin on 05-05-2013

b in a comfortable-jawed vise. Install two nuts on the studs and use the outer nut to install the studs. Vehicles equipped with ABS 3. Position the ABS sensor and install the bolt. All vehicles 4. Place the brake disc shield. 5. NOTE: Apply a coat of Ford Excessive Temperature 4×4 Front Axle and Wheel Bearing Grease E8TZ-19590-A meeting Ford specification ESA-M1C198-A to the O-ring area of the wheel hub and bearing before putting in the hub…

Ford DPFE Sensor Installation Instructions

34

Filed Under (Ford) by admin on 03-01-2012

…ct tabs and pull the harness out. Use a socket wrench to loosen and remove the sensor’s screws. Raise the sensor off the mount. 4. Wipe the mount clean with a rag. This will ensure a clean connection for the new sensor. 5. Set up the new DPFE sensor. Place the sensor on the mount. Safe the sensor with the 2 screws and tighten with the socket wrench. Plug the hoses into the new sensor. Join the wire harness; the harness will click on into pl…

1998 Chevy Truck Evaporator Core Service and Repair Page 2

26

Filed Under (Chevrolet) by admin on 29-01-2012

ator case retaining screws. Tighten to 2.5 N.m (24 in lb). 3. Install the evaporator core meeting to the vehicle. 4. Install the bolts which retain the evaporator case to the bulkhead. Tighten the bolts to 4.5 N.m (40 lb in). 5. Install the condenser to the evaporator line fitting. Install the accumulator. 6. Install the evaporator case bolts and screws. Tighten to 2.5 N.m (24 In in). Set up the blower motor resistor. 7. Install the evaporator ca…

Ford Focus Oxygen/O2 Sensor Installation Instructions

28

Filed Under (Ford) by admin on 20-04-2013

…formed you was bad. The sensor screws into portholes in the exhaust pipes forward of the catalytic converter. There may be one close to the manifold within the front pipe area and another one close to the catalytic converter. 5. Comply with the wire of the O2 Sensor to the plug and unplug it. Use the flathead screwdriver to press in the clip lock and separate the plug. 6. Place the oxygen sensor socket onto the ratchet and remove the O2 sensor fr…

2001 F-150 Intake Manifold 5.4L Installation Procedure

36

Filed Under (Ford) by admin on 17-01-2012

2001 Ford F-150 Intake Manifold 5.4L Installation Procedure : 1. CAUTION: Do not use metallic scrapers, power abrasive discs or any abrasive means to scrub the sealing surfaces, these instruments cause scratches and gouges that make leak paths. Use a plastic scraper only. Clean all the sealing surfaces. 2. If eliminated, install the water crossover. 3. Install the intake manifold. Place the new intake manifold gaskets. Place the upper intake man…

Ford Truck O2/Oxygen Sensor Installation Instructions

38

Filed Under (Ford) by admin on 20-04-2013

…fter the catalytic converter. Heated oxygen sensors come with three wires. If yours is a unique sort, it can have one or two wires. The part is just like a spark plug. 4. Unplug the oxygen sensor’s electrical connector. 5. Take away the sensor using a sensor socket and ratchet. 6. Set up the new unit by hand first to avoid injury to the threads. Then use a torque wrench and sensor socket for closing adjustments. Torque the sensor to 36 ft.-…

You might also likeclose