Search Result for " 2006 pontiac g6 diagram of power steering" :

Install Power Steering Pressure and/or Return Hose Assembly

39

Filed Under (Buick, Pontiac) by admin on 02-05-2013

ing pump assembly. Take away the bolt/screws from the retaining clips. 5. Disconnect the ability steering strain hose from the ability steering gear assembly. Take away the power steering stress hose meeting from the vehicle. 6. Set up the ability steering pressure hose assembly to the vehicle. Join the power steering strain hose to the facility steering pump assembly. 7. Connect the facility steering stress hose to the power steering gear assemb…

Toyota Steering Intermediate Shaft Noise Repair

26

Filed Under (Toyota) by admin on 17-12-2011

shaft sub-assembly with the bolt. Torque: 35.three Nm (360 kgfcm, 26 ftlbf) c. Set up the steering column hole cowl to the steering gap cowl boot. d. Join the clamp to the steering column gap cover boot and tighten the bolt. 6. Take away the steering wheel holder from the car (if used). 7. Road test the car to confirm the restore and make sure that the steering wheel is centered….

Ford Focus Steering Rack Installation Instructions

32

Filed Under (Ford) by admin on 19-02-2012

sion jack and subframe alignment pins to reconnect the ability steering hoses. Tighten the hose assist clamp and change the heat shield. Safe the support insulator to the transaxle middle bolt with a torque of 37 foot pounds. 6. Join the cooler hose and relink the stabilizer bars to the struts and springs (37 foot pound torque). Tighten the new tie rod end nuts to 35 foot-pounds and exchange the wheels. You may decrease the front end at this poin…

Ford Focus Power Steering Pump Installation Instructions

39

Filed Under (Ford) by admin on 30-04-2013

…f the pump, and drain the pump into the cup. 3. Take away the nuts which can be holding the pump onto the firewall, utilizing the wrench. Remove the belt on the pump from the pulley. Pull the old pump from the engine housing. 4. Secure the new pump onto the firewall with the securing nut. Exchange the belt to the pulley on the pump. Exchange the strains to the right holes on the pump. Tighten the nuts on the firewall and pump lines. Fill the pump…

Buick Steering Wheel Installation Instructions

30

Filed Under (Buick) by admin on 29-03-2013

…ering wheel puller tool onto the steering wheel and break the steering wheel loose from the steering column. Remove the steering wheel bolt and nut with a socket wrench and pull the old steering wheel off the steering column. 6. Place the new steering wheel onto the steering column and secure it with the nut and bolt. 7. Reattach the horn cap and its electrical connector as well as the steering wheel cover and its electrical connector. Secure the…

Ford Windstar Rack and Pinion Installation Instructions

35

Filed Under (Ford) by admin on 03-05-2013

…frame, which is subsequent to the steering rack. Use the jack to lift the subframe up to the physique till you may reattach the subframe bolts to the chassis. Torque the bolts to 85 foot-kilos with the 3/8-inch torque wrench. 4. Reinstall the exhaust flex tube to the exhaust using the 3/8-inch ratchet, extension and sockets. Set up the entrance wheels with the tire wrench. Reconnect the steering column to the rack and pinion utilizing the replace…

Honda VFR Powerlet Steering Head Kit Installation

32

Filed Under (Honda) by admin on 29-04-2014

motor. Observe the clutch hose out toward the underside of the Steering Head tube. Route the harness up into the Steering Head tube. Connect the black wire to the radiator mounting bolt or different chassis bolt in the area. 4. Set up the fuse in the fuse-holder. The middle terminal is plus and the outer ring is negative. Apply both dielectric grease or Vaseline to the spade terminals. Join the purple wire to the positive spade terminals &…

Ford Super Duty Power Door Lock Actuator Installation Instructions

34

Filed Under (Ford) by admin on 31-10-2012

…ok the Super Duty’s new power lock actuator onto the lock rod by hand. Connect the power lock actuator to the door with the retaining bolt. Plug the lock wiring connector into the brand new power lock actuator manually. 6. Put the Super Duty’s door panel again on the truck door by reversing your removing steps….

Vibration in Steering Wheel, Floor, Seat at Highway Speeds

35

Filed Under (Buick, Cadillac, Oldsmobile, Pontiac) by admin on 18-01-2012

le Aurora 2000-2005 Pontiac Bonneville (17″ Tires only) Condition A few consumers might comment on shaking/vibration in the steering wheel, floor or seat at the same time as driving at highway speeds (most often between 60-72 mph (ninety six-a hundred and fifteen km/h)) on smooth roads. Those specific cars could also be delicate to quite a lot of rotating mass assemblies, particularly if they’re regarded as to be out-of-balance. Corre…

Ford Power Window Regulator Installation Instructions

40

Filed Under (Ford) by admin on 21-11-2012

…the Ford’s window glass to the highest of the window body and tape it there with packing tape. 5. Remove the retaining bolts from the window regulator on the window glass, door assist and window motor with a socket set. 6. Pull out the Ford’s outdated power window regulator and exchange it with the new one. Bolt the brand new power window regulator to the door assist, window glass and power windows motor with the socket set. 7. Reinst…

You might also likeclose