2004 grand prix leaking water in floor

You search Auto repair manual PDF about 2004 grand prix leaking water in floor, search results will appear below. If search results do not exist, please search by others keyword.

2004-2005 Pontiac Grand Prix Plenum Water Deflector

32

Filed Under (Buick, Pontiac) by admin on 14-01-2012

e the windshield wipers in the up position. 2. Open the hood. 3. Take away the hood seal. 4. Take away the washer hose from the precise air inlet grille panel. 5. Remove the push pin that retains the air inlet grille panel. 6. Remove the air inlet grille panel. 7. Discard the rubber water deflector. 8. Install the new designed plenum water deflector. 9. Set up the air inlet grille panel. 10.Install the push pins. 11. Install the washer hose. 12…

Ford Windstar Water Pump Installation Instructions

29

Filed Under (Ford) by admin on 14-04-2013

…so that you can push it towards the rear of the van. Take away the accessory drive belt when done. 4. Remove the water pump pulley with the correct-sized wrench. 5. Detach the drive belt tensioner with the socket and ratchet. 6. Take away the lower radiator and heater hose from the water pump with a flat head screwdriver to loosen the clamps. 7. Unscrew the bolts from the water pump with the socket and ratchet then pull it away from the engine. 8…

Ford F-150 Water Pump Removal and Installation Instructions

22

Filed Under (Ford) by admin on 15-11-2012

se until the clamp is loose. The water pump is situated on the entrance of the engine block dealing with the fan. 5. Pull each hose away from the water pump meeting by hand till the hoses are disconnected from the water pump. 6. Take away the four bolts connecting the water pump pulley to the water pump by turning them counterclockwise with a socket, socket extension and socket-wrench whereas the fan-drive belt is still installed. 7. Take away th…

Ford F-250 7.3 Diesel Water Pump Removal Instructions

26

Filed Under (Ford) by admin on 10-06-2013

…m the radiator then tighten the drain valve. 2. Open the hood. Remove the overflow hose from the white plastic coolant tank on the high of the engine with a pair of pliers. Remove the three holding screws from the tank with a 5/16-inch nut driver. Take away the tank from the engine bay. 3. Take away the upper radiator hose by squeezing the clamps with a pair of pliers while pulling the hose from the radiator and the water pump. Place a ½-inch rat…

Ford Truck Water Pump Installation Instructions

32

Filed Under (Ford) by admin on 23-05-2013

…tensioner to return the belt to its correct tension. 4. Attach every radiator hose, one on the far side and one on the close to facet, to the water pumps and secure then with the the hose clamps tightened with a screwdriver. 5. Open the radiator cap and fill it with coolant. Start the automotive to distribute coolant all through the system, then turn off the automotive and high off the coolant level….

Ford F-Series Water Pump Installation Instructions

26

Filed Under (Ford) by admin on 04-08-2012

ay the coolant reservoir hose from the fan shroud. 5. Loosen the fan clutch assembly with the special fan clutch removal tools. Rotate the fan and clutch meeting slowly counterclockwise until they release from the water pump. 6. Place the complete assembly into the hole the fan shroud came out of. Remove the fan clips from the fan shroud, if it has any. Remove the Water Pump 1. Elevate the Ford F-series truck with a jack, using jack stands to sho…

Ford 7.3 Turbo Diesel Water Pump Installation Instructions

42

Filed Under (Ford) by admin on 20-02-2012

ose. Reinstall the serpentine belt and tighten the four pulley bolts. Elevate the fan shroud and fan into the engine bay. Reattach the fan shroud bolts. Utilizing the fan nut wrench, reattach the fan to the water pump pulley. 6. Reinstall the coolant tank and upper and lower radiator hoses. Remove the cap from the coolant tank and add 4 gallons of antifreeze, four gallons of distilled water, and one bottle of coolant conditioner. Screw the cap ag…

1997 Buick Regal GS Pontiac Grand Prix GTP Fuel Pump Resistor Replacement

27

Filed Under (Buick, Pontiac) by admin on 22-03-2013

stic push-in retainers that attach the windshield washer solvent reservoir to the radiator help and the one nut that attaches it to the strut tower. 5. Reposition the reservoir for access to the realm rearward of the battery. 6. Elevate the car on a hoist. At the right front wheel opening, remove the three screws that connect the inside fender splash shield to the entrance fascia at the wheel opening and the 2 screws that attach it to the bottom…

1998 Buick Regal GS Pontiac Grand Prix GTP Fuel Pump Resistor Replacement

25

Filed Under (Buick, Pontiac) by admin on 04-03-2013

the two screws that attach it to the bottom of the fascia. It’s not essential to remove the other interior fender splash protect screws. 5. Reposition the interior fender splash protect to access the fuel pump resistor. 6. Remove the 2 bolts attaching the windshield washer reservoir to the rear mounting bracket and remove the one bolt attaching the bracket to the body. 7. From beneath the vehicle, using a 10mm box or open end wrench, take a…

Ford Water Pumps Installation Instructions

35

Filed Under (Ford) by admin on 08-06-2013

…osen it by eradicating the timing belt tensioner with the socket and ratchet. Pull the timing belt off. 5. Remove the water pump and clean any remaining gasket materials from the water pump mounting floor with a scraper tool. 6. Put a brand new gasket on the water pumps mounting surface and set the new water pump into place. Tighten the bolts on the water pumps with a torque wrench set to 13 ft.-lbs. 7. Reinstall the timing belt within the correc…

You might also likeclose