Search Result for " 2003 chevrolet trailblazer power steering diagram" :

Install Power Steering Pressure and/or Return Hose Assembly

39

Filed Under (Buick, Pontiac) by admin on 02-05-2013

ability steering fluid. 3. Remove the ability steering gear assembly warmth shield. 4. Disconnect the facility steering stress hose from the facility steering pump assembly. Take away the bolt/screws from the retaining clips. 5. Disconnect the ability steering strain hose from the ability steering gear assembly. Take away the power steering stress hose meeting from the vehicle. 6. Set up the ability steering pressure hose assembly to the vehicle….

Toyota Steering Intermediate Shaft Noise Repair

26

Filed Under (Toyota) by admin on 09-10-2014

shaft sub-assembly. a. Align the match-mark with the one on the steering sliding yoke sub-assembly and the shaft assembly. b. Install the steering sliding yoke sub-meeting with the bolt. Torque: 35.3 Nm (360 kgfcm, 26 ftlbf) 5. Connect the intermediate shaft sub-assembly. a. Align the match-marks on the steering intermediate shaft sub-assembly and the steering gear assembly. b. Install the shaft sub-assembly with the bolt. Torque: 35.three Nm (3…

Ford Focus Steering Rack Installation Instructions

32

Filed Under (Ford) by admin on 19-02-2012

haft and replace the unique flooring seal. Use pins to align the crossmember to chassis alignment holes and secure the crossmember with outer bolts tightened to 85 foot kilos and 4 interior bolts tightened to 148 foot pounds. 5. Take away the transmission jack and subframe alignment pins to reconnect the ability steering hoses. Tighten the hose assist clamp and change the heat shield. Safe the support insulator to the transaxle middle bolt with a…

Ford Focus Power Steering Pump Installation Instructions

39

Filed Under (Ford) by admin on 30-04-2013

…f the pump, and drain the pump into the cup. 3. Take away the nuts which can be holding the pump onto the firewall, utilizing the wrench. Remove the belt on the pump from the pulley. Pull the old pump from the engine housing. 4. Secure the new pump onto the firewall with the securing nut. Exchange the belt to the pulley on the pump. Exchange the strains to the right holes on the pump. Tighten the nuts on the firewall and pump lines. Fill the pump…

Buick Steering Wheel Installation Instructions

30

Filed Under (Buick) by admin on 29-03-2013

…ff the steering wheel. 3. Remove the horn cap and its electrical connector and pull it off the steering wheel. 4. Loosen the steering wheel bolt and nut at the rear of the steering wheel, connecting it to the steering column. 5. Place the steering wheel puller tool onto the steering wheel and break the steering wheel loose from the steering column. Remove the steering wheel bolt and nut with a socket wrench and pull the old steering wheel off the…

Ford Windstar Rack and Pinion Installation Instructions

35

Filed Under (Ford) by admin on 03-05-2013

…frame, which is subsequent to the steering rack. Use the jack to lift the subframe up to the physique till you may reattach the subframe bolts to the chassis. Torque the bolts to 85 foot-kilos with the 3/8-inch torque wrench. 4. Reinstall the exhaust flex tube to the exhaust using the 3/8-inch ratchet, extension and sockets. Set up the entrance wheels with the tire wrench. Reconnect the steering column to the rack and pinion utilizing the replace…

Honda VFR Powerlet Steering Head Kit Installation

32

Filed Under (Honda) by admin on 29-04-2014

motor. Observe the clutch hose out toward the underside of the Steering Head tube. Route the harness up into the Steering Head tube. Connect the black wire to the radiator mounting bolt or different chassis bolt in the area. 4. Set up the fuse in the fuse-holder. The middle terminal is plus and the outer ring is negative. Apply both dielectric grease or Vaseline to the spade terminals. Join the purple wire to the positive spade terminals &…

Ford F250 Gasoline Serpentine Belt Installation Instructions

22

Filed Under (Ford) by admin on 03-01-2012

…ine. 3. Connect the belt tensioner tool to the serpentine belt tensioner. Move the tensioner aside with the software and slip the serpentine belt over the tensioner pulley, per your F250′s specific belt-routing diagram. 4. Release the pressure on the tensioner with the software, then remove the device and shut the hood. Belt-routing diagrams range from mannequin year to mannequin 12 months and likewise by the F250′s specific accent se…

Ford Super Duty Power Door Lock Actuator Installation Instructions

34

Filed Under (Ford) by admin on 31-10-2012

…ator together with your socket set. 4. Swivel the power lock actuator to unhook the actuator from the Super Duty’s lock rod by hand. Take the old energy lock actuator from the door and replace it with the brand new one. 5. Hook the Super Duty’s new power lock actuator onto the lock rod by hand. Connect the power lock actuator to the door with the retaining bolt. Plug the lock wiring connector into the brand new power lock actuator man…

Idle Fluctuation and/or the MIL Is On With DTC P1129 and/or P0505 Page 1

31

Filed Under (Honda) by admin on 26-03-2013

hooting. Repair Procedure A 1. Connect the HDS to the car’s DLC. 2. Start the engine, and turn on the HDS. 3. When prompted, enter the VIN and the odometer reading. 4. From the System Choice Menu display, choose PGM-FI. 5. From the Mode Menu, select DATA LIST. 6. Scroll down the checklist to PSP SWITCH. Watch the studying in the Worth column. 7. Examine for a broken power steering pressure swap wire by wiggling the P/S stress change wire ha…

You might also likeclose