2002 silverado leaking antifreeze

You search Auto repair manual PDF about 2002 silverado leaking antifreeze, search results will appear below. If search results do not exist, please search by others keyword.

Ford Taurus Heater Bypass Installation Instructions


Filed Under (Ford) by admin on 05-01-2012

…er, which is just a short pipe that may be bought at any auto parts store and is inexpensive. The heater hoses shouldn’t be cut as a result of they are expensive and can be wanted again when the heater core is replaced. 3. Fill the radiator to the correct degree with antifreeze and leave the radiator cap off for the moment. Start the engine and permit it to heat up. Once the engine warms sufficient to open the thermostat, the fluid level wi…

Loss of Communication with Brake Module (Reground EBCM Ground)


Filed Under (Cadillac, Chevrolet, GMC, Oldsmobile) by admin on 09-04-2013

eneath the driving force’s facet door. If a number of grounds are discovered on this location, the EBCM ground will be recognized as the heavy (12-gauge) wire. 2. Clear the world, front and back, utilizing a Whiz Wheel. 3. Set up the bottom, then the washer and then the bolt to the frame. Necessary: It is important to use the bolts, washers and nuts specified in this bulletin. These parts have been identified because of their conductive fin…

2002 Peugeot 206 Thermostat Installation Instructions


Filed Under (Peugeot) by admin on 22-02-2012

chamber. Unfasten the clamp holding the lower radiator hose in place. Take away the lower radiator hose and permit the coolant to drain out of the radiator and growth chamber. Reconnect the hose to the radiator when finished. 3. Locate the higher radiator hose and comply with it along the proper facet of the engine bay till it ends on the thermostat housing on the engine block. Unfasten the clamp holding the higher radiator hose in place and disc…

2001-2002 Honda Accord Distributor Replacement Procedures


Filed Under (Honda) by admin on 09-07-2012

s, however from 2000 to 2002, all Honda Accords had distributors. In 1999 and earlier, the Accord had each distributor and distributorless systems. 2001-2002 Honda Accord 2.2L and 2.3L Engines, 1996-2000 Honda Accord 2.7L and 3.0L Engines Distributor Replacement Instructions 1. Discover the distributor on the engine block; the spark plug cables lead to it. Unhook the negative cable from the battery; it will be within the entrance and driver’…

1998-2002 Toyota Corolla Exterior Door Handles Installation Instructions


Filed Under (Toyota) by admin on 24-02-2012

oor handle in place. Remove the small pole that controls the door latch; it is clipped to the higher portion of the handle from the clip that is in the upper portion of the previous door handle. Take away the old door handle. 3. Place the brand new handle into the hole. Clip the small pole into the clip of the upper portion of the new handle. Take a look at the handle to ensure the door latches and unlatches properly. Set up the three 10 millimet…

1998-2002 Honda Accord V6 Comptech Supercharger Kit – Page 2


Filed Under (Honda) by admin on 05-03-2013

re against the bracket to distort plate or push it out, this spacer is only designed to take up inconsistencies in factory head. Whereas holding spacer with a 19mm wrench, insert supplied 10mm bolt into gap and torque bolt to 28ft-lbs. Torque cam seal bolts (B) to 15ft/lbs. Change EGR valve, utilizing provided gasket, and torque to 15ft/lbs. Substitute electrical plug. 12. Blower preparation : Blower has (6) bolts around enter shaft. Lower (4) bo…

1998-2002 Honda Accord V6 Comptech Supercharger Kit


Filed Under (Honda) by admin on 05-03-2013

stock decrease air box. Take away (2) bolts holding air box to sub-frame. Decrease & take away inventory air-box. Take away inventory bracket in engine bay. Remove small rubber grommet in sub-frame subsequent to battery. 3. Radiator hose : Remove inventory higher radiator hose from engine & radiator. Take away spring clamps & reuse on new silicon hose in kit. (Substitute hoses are available exclusively by way of Comptech part 355-1…

Radiator Installation Instructions for Honda Civic


Filed Under (Honda) by admin on 31-03-2013

…properly. 2. Remove the upper and decrease radiator hoses, using the pliers to compress the spring clamps and remove them. Pull the sensor out of the radiator next to the hose pipe (an o-ring holds the pipe in the radiator). 3. Place the pan beneath the transmission cooler lines. Take away the 2 transmission cooler lines on the bottom of the radiator, utilizing a wrench. Unplug the electrical connectors to the radiator fan. 4. Take away the 10mm…

Ford F-250 7.3 Diesel Water Pump Removal Instructions


Filed Under (Ford) by admin on 10-06-2013

…Remove the overflow hose from the white plastic coolant tank on the high of the engine with a pair of pliers. Remove the three holding screws from the tank with a 5/16-inch nut driver. Take away the tank from the engine bay. 3. Take away the upper radiator hose by squeezing the clamps with a pair of pliers while pulling the hose from the radiator and the water pump. Place a ½-inch ratchet wrench into the square hole on the serpentine belt tensio…

Fuel Filter Removal/Installation Procedure on 5.3L Flexible Fuel Engine


Filed Under (Chevrolet) by admin on 16-01-2012

gs with a shop towel before disconnecting. This will catch any gasoline that may leak out. Place the towel in an approved container when the disconnection is complete. 1. Disconnect the negative battery cable. 2. Set up the J 34730-1A. 3. Loosen the fuel fill cap as a way to relieve gas tank vapor pressure. 4. Open the valve on the J 34730-1A to be able to bleed the system pressure. The gas connections are now secure for servicing. 5. Drain any g…

You might also likeclose