2002 chevy silverado zerk locations

You search Auto repair manual PDF about 2002 chevy silverado zerk locations, search results will appear below. If search results do not exist, please search by others keyword.

Ford F-150 Zerk Fittings Installation Instructions

22

Filed Under (Ford) by admin on 20-02-2012

…hreaded hole by hand to cut back the opportunity of cross-threading the hole. Proceed tightening the fitting with a wrench till the hex flats on the becoming backside out on the part’s surface. Don’t over-tighten. 4. Set up the part on the vehicle. To grease the part, slide the grease gun’s nozzle over the Zerk fitting’s nipple and hold it in place with one hand. Function the deal with of the grease gun to inject grease in…

Loss of Communication with Brake Module (Reground EBCM Ground)

27

Filed Under (Cadillac, Chevrolet, GMC, Oldsmobile) by admin on 09-04-2013

Set up the bottom, then the washer and then the bolt to the frame. Necessary: It is important to use the bolts, washers and nuts specified in this bulletin. These parts have been identified because of their conductive finish. 4. Install a washer and nut to the back facet of the frame. Tighten Tighten the nut to 9 N·m (seventy nine lb in). 5. Cover the front and back aspect of the restore area using Rubberized Undercoating. An additional test may…

2002 Peugeot 206 Thermostat Installation Instructions

36

Filed Under (Peugeot) by admin on 22-02-2012

tor hose and comply with it along the proper facet of the engine bay till it ends on the thermostat housing on the engine block. Unfasten the clamp holding the higher radiator hose in place and disconnect it from the housing. 4. Use a ratchet and socket to take away the two bolts holding the housing in place. Take away the thermostat housing and set it aside. Note the orientation of the thermostat before eradicating it. The brand new thermostat m…

1998-2002 Toyota Corolla Exterior Door Handles Installation Instructions

38

Filed Under (Toyota) by admin on 24-02-2012

mall pole into the clip of the upper portion of the new handle. Take a look at the handle to ensure the door latches and unlatches properly. Set up the three 10 millimeter bolts and tighten. Reattach the clear plastic lining. 4. Place the remaining portion of the door panel onto the six plastic clips on the outer portion of the panel. Pull it over the inside door lock. Make sure that the interior door opener can be positioned by way of the suppli…

2001-2002 Honda Accord Distributor Replacement Procedures

34

Filed Under (Honda) by admin on 09-07-2012

ariety of bolts varies in line with the year. 3. Get the piston within the No. 1 cylinder to the High Dead Middle (TDC) spot. If it isn’t at TDC, the engine won’t work correctly after you exchange the distributor. 4. Install a flippantly greased new O-ring on the end of the distributor shaft and put your new Honda Accord distributor into position. Make sure to buy a brand new O-ring for a comfortable fit. The distributor number is 836…

1998 Chevy Truck Evaporator Core Service and Repair Page 1

32

Filed Under (Chevrolet) by admin on 23-01-2012

Subject : Evaporator Core Service and Repair Manual A/C Removal Procedure Models : 1998 Chevrolet (Chevy) Truck S10/T10 Blazer 2WD V6-4.3L VIN W Evaporator Core Removal Procedure : 1. Disconnect the adverse battery cable. 2. Take away the appropriate side instrument panel sound insulator. Remove the instrument panel storage compartment. 3. Disconnect the passenger facet SIR. Remove the lower proper instrument panel mounting bolt. 4. Take away th…

1998 Chevy Truck Evaporator Core Service and Repair Page 2

26

Filed Under (Chevrolet) by admin on 29-01-2012

Subject : Evaporator Core Service and Repair Manual A/C Installation Procedure Models : 1998 Chevrolet (Chevy) Truck S10/T10 Blazer 2WD V6-4.3L VIN W Evaporator Core Installation Procedure : 1. Install the evaporator core. Assemble the evaporator case sections. 2. Install the evaporator case retaining screws. Tighten to 2.5 N.m (24 in lb). 3. Install the evaporator core meeting to the vehicle. 4. Install the bolts which retain the evaporator cas…

1998-2002 Honda Accord V6 Comptech Supercharger Kit – Page 2

34

Filed Under (Honda) by admin on 05-03-2013

re against the bracket to distort plate or push it out, this spacer is only designed to take up inconsistencies in factory head. Whereas holding spacer with a 19mm wrench, insert supplied 10mm bolt into gap and torque bolt to 28ft-lbs. Torque cam seal bolts (B) to 15ft/lbs. Change EGR valve, utilizing provided gasket, and torque to 15ft/lbs. Substitute electrical plug. 12. Blower preparation : Blower has (6) bolts around enter shaft. Lower (4) bo…

1998-2002 Honda Accord V6 Comptech Supercharger Kit

34

Filed Under (Honda) by admin on 05-03-2013

y. Don’t remove manifold side until throttle physique has been relocated. Mark every coolant hose as they are disconnected. Don’t cross hoses throughout reassembly. Take away engine breather hose from valve cover. 4. Alternator harness : Take away bolt holding plastic cowl over wiring harness. Open snap clips on plastic cover & take away from wire harness. These wires might be rerouted along groove between plastic mount & co…

Fuel Filter Removal/Installation Procedure on 5.3L Flexible Fuel Engine

34

Filed Under (Chevrolet) by admin on 16-01-2012

Subject : Use of New Special Tool J 46363 – Fuel Line Disconnect Tool for Fuel Filter Removal/Installation Procedure on 5.3L Flexible Fuel Engine (RPO L59) Models : 2002-2003 Chevrolet Silverado, Tahoe 2002-2003 GMC Sierra, Yukon with 5.3L Flexible Fuel Engine (VIN Z — RPO L59) Some 2002-2003 autos could also be outfitted with a 5.3L Flexible Fuel Engine. A new device and procedure has been launched for the removal and installation o…

You might also likeclose