2001 pontiac bonneville tension pulley diagram

You search Auto repair manual PDF about 2001 pontiac bonneville tension pulley diagram, search results will appear below. If search results do not exist, please search by others keyword.

Ford Bronco Tensioner Pulley Installation Instructions


Filed Under (Ford) by admin on 14-03-2013

…th a new one and safe it to the tension meeting utilizing the existing tension pulley retaining bolt by the center of the pulley. Tighten it to 30 foot-kilos of torque before securing the tension assembly again on the engine. 5. Safe the tension pulley assembly to the engine using the armature retaining bolt and tighten to 30 foot-kilos of torque. Pull the Ford Bronco’s serpentine belt over the strain pulley with the tension pulley still lo…

1997-2000 Honda CR-V Timing Belt Replacement Procedures


Filed Under (Honda) by admin on 29-05-2012

the 9 o’clock position. 4. Help the engine with the floor jack. Take away the left engine mount and the valve cowl using the appropriate sockets. Verify that the letters “UP” are on the 12 o’clock position on each camshafts. 5. Take away the crankshaft pulley bolt using the pulley holder, handle and socket. Take away the crankshaft pulley, upper and decrease timing belt covers, and the guide washer on the crankshaft sprocket. Examine that the ti…

Ford F250 Gasoline Serpentine Belt Installation Instructions


Filed Under (Ford) by admin on 03-01-2012

…ine. 3. Connect the belt tensioner tool to the serpentine belt tensioner. Move the tensioner aside with the software and slip the serpentine belt over the tensioner pulley, per your F250′s specific belt-routing diagram. 4. Release the pressure on the tensioner with the software, then remove the device and shut the hood. Belt-routing diagrams range from mannequin year to mannequin 12 months and likewise by the F250′s specific accent se…

Install Power Steering Pressure and/or Return Hose Assembly


Filed Under (Buick, Pontiac) by admin on 02-05-2013

ability steering fluid. 3. Remove the ability steering gear assembly warmth shield. 4. Disconnect the facility steering stress hose from the facility steering pump assembly. Take away the bolt/screws from the retaining clips. 5. Disconnect the ability steering strain hose from the ability steering gear assembly. Take away the power steering stress hose meeting from the vehicle. 6. Set up the ability steering pressure hose assembly to the vehicle….

Honda V6 Engine Serpentine Belt Installation Instructions


Filed Under (Honda) by admin on 02-07-2012

…es pressure on the belt. Pull the belt off the tensioner pulley. 4. Remove the belt from the remaining pulleys and raise the old belt out of the engine bay. Full this step from the engine bay and not from beneath the vehicle. 5. Place the brand new belt into the engine bay and route the belt around all the pulleys besides the tensioner pulley. Use your diagram as a guide. 6. Get under the Honda V6 again, push up on the ratchet driver handle and s…

1998-2002 Honda Accord V6 Comptech Supercharger Kit – Page 2


Filed Under (Honda) by admin on 05-03-2013

re against the bracket to distort plate or push it out, this spacer is only designed to take up inconsistencies in factory head. Whereas holding spacer with a 19mm wrench, insert supplied 10mm bolt into gap and torque bolt to 28ft-lbs. Torque cam seal bolts (B) to 15ft/lbs. Change EGR valve, utilizing provided gasket, and torque to 15ft/lbs. Substitute electrical plug. 12. Blower preparation : Blower has (6) bolts around enter shaft. Lower (4) bo…

Peugeot 206 1.9 Diesel Alternator Belt Installation Instructions


Filed Under (Peugeot) by admin on 22-02-2012

ly. Pull the belt off the remaining pulleys. Pull the belt out from the engine compartment. 4. Place the new belt across the pulleys. Follow the diagram to position the belt around the pulleys apart from the tensioner pulley. 5. Pull the tensioner pulley with a socket wrench. Place the belt around the pulley. Slowly release the tensioner to tighten the belt. 6. Start the automotive to observe the belt. The belt should transit smoothly across the…

Honda Civic Timing Belt Replacement Instructions


Filed Under (Honda) by admin on 02-07-2012

…edge of the cylinder head, and the mark at 7 o’clock should align with a mark on the block. If they aren’t shut, turn the crankshaft another revolution and they will line up. Solely when the marks are excellent proceed. 5. Remove the crankshaft pulley bolt using a socket. Pull off the pulley. Take away the lower timing cowl using a 10 mm socket. Loosen the timing belt tensioner and push it away from the belt. Tighten it slightly with a wren…

Toyota Corolla Timing Belt Installation Instructions


Filed Under (Toyota) by admin on 30-03-2013

…of the tension. Loosen the belt tensioner an allow it to use rigidity on the belt. Set up the belt guide washer on the crankshaft. Flip the crankshaft two turns and realign the timing marks. Tighten the belt tensioner bolt to 27 foot kilos of torque. Install all parts in reverse order of removal and at last tighten the crankshaft bolt to 87 foot pounds of torque….

Vibration in Steering Wheel, Floor, Seat at Highway Speeds


Filed Under (Buick, Cadillac, Oldsmobile, Pontiac) by admin on 18-01-2012

ill simplify Step five by no longer requiring dial indicators. If a Hunter GSP9700 gadget is to be had, it can be used to measure the radial pressure of the tire/wheel assembly. A guideline right here is eighteen lbs or less. 5. While on the balancer, degree wheel runout. If radial or lateral runout exceeds .020 in (0.50 mm) for aluminum wheels (.030 in (0.seventy six mm) for metal wheels), change the wheel. 6. After confirming wheel stability an…

You might also likeclose