Filed Under (Ford) by admin on 27-10-2012
nna outlet on the rear panel of the aftermarket radio. 5. Place the again of the new stereo at the opening of the stereo mounting dock. Slide the stereo straight into the opening until the stereo snaps into place in the dock. 6. Exchange the grounding cable clamp over the unfavorable lead submit, and tighten the clamp with the socket and ratchet. Ford Windstar Radio/Stereo Installation Tips You should use the Ford installation sleeve with all Win…
Filed Under (Ford) by admin on 29-05-2013
…ll they8217;re tight. 5. Modify the hitch forward or back and to the left or right by pushing it till the biggest hole on the hitch matches up with the largest hole on the frame. Tighten the bolts with a ratchet and socket. 6. Locate the four remaining holes on the hitch that need to be drilled within the frame for the bolts to go through. There are two holes on each side of the large gap you used to match collectively the hitch and frame earli…
Filed Under (Ford) by admin on 03-05-2013
…frame, which is subsequent to the steering rack. Use the jack to lift the subframe up to the physique till you may reattach the subframe bolts to the chassis. Torque the bolts to 85 foot-kilos with the 3/8-inch torque wrench. 4. Reinstall the exhaust flex tube to the exhaust using the 3/8-inch ratchet, extension and sockets. Set up the entrance wheels with the tire wrench. Reconnect the steering column to the rack and pinion utilizing the replace…
Filed Under (Ford) by admin on 06-03-2013
mounting dock. Pull the wiring harness adapter into the front of the adapter. 4. Attach the plugs of the wiring harness adapter within the retailers on back of the radio. Push the radio into the opening of the mounting dock. 5. Connect the destructive battery clamp across the adverse lead publish of the battery. Use the wrench to tighten and prevent the clamp from shifting freely….
Filed Under (Ford) by admin on 14-04-2013
…so that you can push it towards the rear of the van. Take away the accessory drive belt when done. 4. Remove the water pump pulley with the correct-sized wrench. 5. Detach the drive belt tensioner with the socket and ratchet. 6. Take away the lower radiator and heater hose from the water pump with a flat head screwdriver to loosen the clamps. 7. Unscrew the bolts from the water pump with the socket and ratchet then pull it away from the engine. 8…
Filed Under (Ford) by admin on 25-05-2013
…vent that they had been removed. Not all models require this step. 5. Reconnect the upper and decrease radiator hoses using the channel lock pliers. Reconnect the transmission cooler lines and reinstall the coolant reservoir. 6. Install the fan and shroud assembly and then set up the hood latch by inserting the bolts. 7. Refill the radiator and the reservoir with the required quantity of coolant. Two to 3 gallons ought to be sufficient….
Filed Under (Ford) by admin on 02-06-2012
Determine the starter wire under the steering wheel and connect the beginning disable relay. Set up any further options utilizing the alarm producer8217;s directions. Connect the entire wires to the alarm management module. 5. Reconnect the positive battery cable and check the alarm. Alter the sensor8217;s sensitivity if necessary….
Filed Under (Ford) by admin on 10-01-2012
…l the radiator with the quantity and type of coolant laid out in your owner8217;s manual. 4. Take away the jack stands and launch the jack. Attach the negative battery cable to the put up and tighten the screw on the clamp. 5. Begin the engine and verify for leaks. Then, close the hood and take the SUV for a test drive….
Filed Under (Ford) by admin on 17-04-2013
ic piece. 5. Pry the air vents situated over the radio meeting out of the Ford Focus dash. Remove the two screws holding the console and radio, and pull the entire heart portion of the sprint out by pulling down from the top. 6. Disconnect the wiring harness from the back of the unit and change out the unique harness adapter for the brand new one. Join the harness to the again of the stereo and slide the unit into the center console trim. 7. Conn…
Filed Under (Ford) by admin on 13-11-2012
ant on the brand new water pump and place the new gasket over this. Hold the gasket in place on the pump as you mount it on the engine, where you removed the old pump. 2. Maintain the water pump in place as you secure it with 4 new bolts. Tighten every in any order with 13 foot pounds torque. Reassemble the rest of the components within the order you took them off the Ford Focus. Exchange any parts that appear worn or broken as you go. 3. Replace…