Filed Under (Ford) by admin on 06-11-2012
…ble into the antenna outlet on the rear panel of the brand new stereo. 5. Slide the brand new unit into the stereo faceplate adapter. Push the unit into the sprint till it locks into place. Return to the Ford’s battery. 6. Place the destructive battery cable clamp over the destructive battery terminal. Tighten the bolt on the clamp with the wrench. Close the Taurus’ hood….
Filed Under (Ford) by admin on 09-09-2012
…ehicle is provided with an automated transmission, it’s a good idea to make use of a hoist with an adjustable engine sling that will allow you to position the engine at an angle as you lower it towards the transmission. 8. Oil the crankshaft pilot bearing on the end and rear of the crankshaft. Use clear engine oil. Apply a small coat of all-objective grease to the transmission enter shaft if you have a manual transmission. 9. Flip the flywh…
Filed Under (Ford) by admin on 06-04-2013
…f the new stereo. Plug the antenna cable into the FM antenna input on the again of the new unit. Slide the stereo into the faceplate adapter until it locks into place within the F-150′s dashboard. Return to the battery. 6. Place the battery cable again onto the battery terminal. Tighten the cable to the terminal with the wrench. Shut the Ford’s hood….
Filed Under (Ford) by admin on 27-10-2012
…rstroke diesel engine to get all of the efficiency and turbo energy that late model Powerstrokes enjoy right off the manufacturing facility floor. Ford Powerstroke Diesel Turbocharger Installation 1. Minimize the exhaust pipe 6 inches after the “Y” pipe meets up with the only exhaust pipe below the passenger compartment of the truck. Loosen and remove the four nuts that hold the exhaust flange together. Pull the “Y” pipe f…
Filed Under (Ford) by admin on 09-04-2013
ess adapter. Connect the opposite finish of the adapter to the wire harness of the new radio. Push the connections collectively and click them into place. Attach the radio antenna to the offered port on the rear of the radio. 5. Slide the related radio into the radio installation sleeve. Push it in until it clicks into place. Reconnect the car battery. Turn on the radio to check the installation….
Filed Under (Ford) by admin on 20-03-2013
…ew head unit into the opening within the dashboard provided by the faceplate adapter. Push the stereo into the dash until it locks into place throughout the stereo mounting dock. Return to the Ford’s engine compartment. 7. Place the battery cable clamp again onto the detrimental battery terminal and tighten the cable’s bolt with the wrench. Shut the hood….
Filed Under (Ford) by admin on 31-10-2012
connector earlier than you start your trip. Ford Edge Trailer Lights Installation Instructions 1. Establish a trailer that will work along with your Ford Edge. The manufacturing unit trailer bundle on the Ford Edge includes a 4-pin connector that you’ll use to put in the trailer lights. When renting or purchasing a trailer, the hitch must match the ball on the trailer hitch and should have a 4-pin connector to work together with your vehicl…
Filed Under (Ford) by admin on 21-04-2014
…the disc won’t detach from the steering knuckle by hand. 7. Spray the brand new rotor with brake cleaner to take away the oil used to protect the disc while in storage. Wipe the surface of the rotor clear with a towel. 8. Place the new rotor on the wheel bolts with the raised center section of the disc going through outward. 9. Return the bracket to the rotor and exchange the bolts with the 15 mm wrench. 10. Place new brake pads in the slo…
Filed Under (Buick, Pontiac) by admin on 14-01-2012
the hood seal. 4. Take away the washer hose from the precise air inlet grille panel. 5. Remove the push pin that retains the air inlet grille panel. 6. Remove the air inlet grille panel. 7. Discard the rubber water deflector. 8. Install the new designed plenum water deflector. 9. Set up the air inlet grille panel. 10.Install the push pins. 11. Install the washer hose. 12. Install the hood seal. 13. Close the hood. 14. Return the windshield wipers…
Filed Under (Ford) by admin on 04-01-2012
…d on your engine. 5. Disconnect the wiring for the alternator on the alternator’s electrical connectors. If the wiring is secured with a bracket, unbolt the bracket with the wrench earlier than you disconnect the wires. 6. Remove the mounting bolts for the alternator utilizing the wrench and lift it off of the engine block. Keep in mind where every mounting bolt went as you’ll need to install them in the same locations. Ford Focus Alt…